Thanks for your reply but it seems like half an answer to me as you didn't tell me what to do with the output of arecord -L?
I found a seemingly relevant thread on the LM forums where someone managed to get their SPDIF working under JACK by writing a custom ALSA config file but there wasn't quite enough hand-holding to get things working for me unfortunately. I have posted all the previously mentioned info on my device as well as the output of arecord -L to
http://linuxmusicians.com/viewtopic.php?f=27&t=8898
Thanks for your help Len and anyone else who can offer me any guidance here!
On Mon, Nov 12, 2012 at 9:00 PM, Len Ovens <len@xxxxxxxxxxxxx> wrote:
Ok, first thing to try is to make sure you can see the s/pdif inout with
On Mon, November 12, 2012 12:11 pm, Dan MacDonald wrote:
> Hello LA land!
>
> I got a Startech USB audio device based on the C-Media CM6206 purely in
> the
> hope of being able to use its S/PDIF input under JACK. It runs JACK just
> fine, I just don't know how I might access the SPDIF input (or even the
> line-in, just out of interest) from under JACK?
>
> When I run alsamixer and switch to viewing the capture ports of the cm6206
> there are 4 capture channels - PCM, Line, Mic and S/PDIF In but under JACK
> I only get 2 capture ports which are the L and R analogue mic input
> channels. I can also see the light emitting from the S/PDIF out port so I
> am confident the S/PDIF should work and hopefully under JACK.
alsa. audacity or arecord should be able to record audio (audacity
provides metering which may make things easier). alsamixer does not show
capture ports it shows volume controls or switches. Often you would have 3
or 4 inputs that are switched/mixed to give one stereo input. So making
sure your s/pdif channel is on/unmuted/turned up is the first step. You
may wish to mute Line and Mic while playing with it. You probably (from
what you have said) have:
Mic-------------\
\
Line----------| Mixer |------PCM------>ALSA-->Jack
/
S/PDIF----------/
Each line here would be a stereo path (two Channels).
In other words I think you will find there are only two input channels to
ALSA.
Assuming this is the device notice this doesn't shows number of channels.
> card 2: Device [USB Sound Device], device 0: USB Audio [USB Audio]
> Subdevices: 1/1
> Subdevice #0: subdevice #0
Or this... but they don't on my 4channel+spdif card either.
> 11: [ 2- 0]: digital audio playback
> 12: [ 2- 0]: digital audio capture
> 13: [ 2] : control
> 33: : timer
Try arecord -L
(Capital L)
It still doesn't show number of outputs directly but rather choices, There
it lists stereo as:
front:CARD=M66,DEV=0
M Audio Delta 66, ICE1712 multi
Front speakers
and spdif as:
iec958:CARD=M66,DEV=0
M Audio Delta 66, ICE1712 multi
IEC958 (S/PDIF) Digital Audio Output
To use my 4 analog inputs I would use:
surround40:CARD=M66,DEV=0
M Audio Delta 66, ICE1712 multi
4.0 Surround output to Front and Rear speakers
This one here _might_ be my analog inputs plus spdif:
surround51:CARD=M66,DEV=0
M Audio Delta 66, ICE1712 multi
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
I say might be because jack actually show 12 inputs:
1-4 are analog
5-8 are not used but defined for the ice1712
9-10 spdif
11-12 monitor mixer output
So the last two inputs in 5.1 might actually be the dead inputs 5-6
--
Len Ovens
www.OvenWerks.net
_______________________________________________ Linux-audio-user mailing list Linux-audio-user@xxxxxxxxxxxxxxxxxxxx http://lists.linuxaudio.org/listinfo/linux-audio-user
