--- Björn Lindström <bkhl@xxxxxxxxxxxxxxx> schrieb: > karsten wiese <annabellesgarden@xxxxxxxx>: > > > Above error message means: > > "usx2yloader can't transfer the firmware to the us122" > > > > So it could be a USB problem. I once had such USB problem with a > > VIA chipset mobo. things didn't work, until i connected my us428 to > > the other USB connector. > > > > Does > > $ dmesg > > say something? > > Nothing very interesting. This is what comes from loading the module > and running fxload: > > usbcore: registered new driver snd-usb-usx2y > usb 2-2: USB disconnect, address 23 > usb 2-2: new full speed USB device using uhci_hcd and address 24 > > > what kind of motherboard do you use? > > Please post outputs of > > $ lspci > > The computer is an IBM ThinkPad R40. The lspci output is as follows: > > 0000:00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset Host Bridge (rev 04) > 0000:00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP Bridge (rev 04) > 0000:00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI > Controller #1 (rev 03) > 0000:00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI > Controller #2 (rev 03) > 0000:00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI > Controller #3 (rev 03) > 0000:00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller > (rev 03) > 0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83) > 0000:00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03) > 0000:00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03) > 0000:00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev > 03) > 0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) > AC'97 Audio Controller (rev 03) > 0000:00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem > Controller (rev 03) > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY > 0000:02:00.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller > 0000:02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05) > 0000:02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller > (PHY/Link) > 0000:02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller > (rev 83) > > I hope you can make something of this. can't ;-) that usx2yloader error should only happen, if something has gone to "dmesg" as well. the chipset is not like the one, i had trouble with. me thinks it'd be best to compile/install a recent kernel with CONFIG_SND_DEBUG_DETECT set and check if dmesg shows something ( like "dsp_load") then. ___________________________________________________________ Telefonate ohne weitere Kosten vom PC zum PC: http://messenger.yahoo.de
