After an upgrade to the suggested alsaconf, the problem remains
unchanged.
By the way, alsaconf from alsa-driver-0.9.5/utils also identifies itself
as version 0.9.0, so as far as I know there was no way to reach your
assumption about which ALSA release I was using based on the information
in my message.
Now: any suggestions as to a fix?
On Fri, 2003-08-08 at 10:27, Gustavo Zamorano S. wrote:
> Joseph:
> Why you are using release 0.9.0?
> I have RH9 and release 0.9.5 that I downloaded a few weeks ago. I
> checked that there is a new release 0.9.6 since end of July.
>
> After compiling the driver, alsaconf remains under the directory
> alsa-driver-0.9.5/utils. It is not copied to /usr/sbin.
>
> I think you should get latest release.
>
> GZS
>
>
>
> Joseph Zitt wrote:
> > Running alsaconf version 0.9.0 under Red Hat 9.0 with the Planet CCRMA
> > kernel and ALSA setup...
> >
> > In running alsaconf to try to configure ALSA for my system's sound card
> > (reported as an "ens1371 Ensoniq 5880 AudioPCI (rev 03)"), I get the
> > following errors:
> >
> > /usr/sbin/alsaconf: line 340: let: a=(>>2) & 0x3f: syntax error: operand
> > expected (error token is ">>2) & 0x3f")
> > /usr/sbin/alsaconf: line 341: let: b=(( & 0x03) << 3) | (( >> 13) &
> > 0x07): syntax error: operand expected (error token is "& 0x03) << 3) |
> > (( >> 13) & 0x07)")
> > /usr/sbin/alsaconf: line 342: let: c=(>> 8) & 0x1f: syntax error:
> > operand expected (error token is ">> 8) & 0x1f")
> > /usr/sbin/alsaconf: line 349: let: v=((>>8)&0xff)|((&0xff)<<8): syntax
> > error: operand expected (error token is ">>8)&0xff)|((&0xff)<<8)")
> >
> > These come from the following function:
> >
> >
> > # convert ISA PnP id number to string 'ABC'
> > convert_isapnp_id () {
> > let a='('$1'>>2) & 0x3f'
> > let b='(('$1' & 0x03) << 3) | (('$1' >> 13) & 0x07)'
> > let c='('$1'>> 8) & 0x1f'
> > strs='@ABCDEFGHIJKLMNOPQRSTUVWXYZ'
> > echo ${strs:$a:1}${strs:$b:1}${strs:$c:1}
> > }
> >
> > which is only called here:
> >
> > # list isapnp cards
> > while read driver cardvendor carddevice data vendor func; do
> > if expr $driver : 'snd-.*' >/dev/null ; then
> > if [ "$last_driver" != "$driver" ]; then
> > echo $driver.o
> > last_driver=$driver
> > fi
> > id1=`convert_isapnp_id $cardvendor`
> > dev1=`swap_number $carddevice`
> > id2=`convert_isapnp_id $vendor`
> > dev2=`swap_number $func`
> > echo "ISAPNP: $id1$dev1=$id2$dev2"
> > fi
> > done < $MODDIR/modules.isapnpmap >> $1
> > }
> >
> >
> > This suggests that there's some problem with the "cardvendor" value...
> > but here I fall off the edge of my knowledge.
> >
> > Does this look familiar, and is there a way to fix it?
> >
> >
>
