Re: [PATCH 4/4] arm64: dts: qcom: sc7280-crd: Add Touchscreen and touchpad support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 11/23/2021 11:28 PM, Matthias Kaehlcke wrote:
On Tue, Nov 23, 2021 at 12:30:13PM +0530, Rajendra Nayak wrote:
From: Kshitiz Godara <kgodara@xxxxxxxxxxxxxx>

Add Touchscreen and touchpad hid-over-i2c node

to which board(s)?

will update


Signed-off-by: Kshitiz Godara <kgodara@xxxxxxxxxxxxxx>
Signed-off-by: Rajendra Nayak <rnayak@xxxxxxxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/sc7280-crd.dts | 63 +++++++++++++++++++++++++++++++++
  1 file changed, 63 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
index 8c2aee6..bef3037 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
@@ -23,6 +23,47 @@
  	};
  };
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+		vdd-supply = <&vreg_l18b_1p8>;
+
+		wakeup-source;
+	};
+};
+
+ap_ts_pen_1v8: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@5c {
+		compatible = "hid-over-i2c";
+		reg = <0x5C>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <500>;
+		hid-descr-addr = <0x0000>;
+
+		vdd-supply = <&vreg_l19b_1p8>;
+	};
+};
+
  &nvme_pwren {
  	pins = "gpio51";
  };
@@ -30,3 +71,25 @@
  &nvme_3v3_regulator {
  	gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
  };
+
+&tlmm {
+	tp_int_odl: tp-int-odl {
+		pins = "gpio7";
+		function = "gpio";
+		input-enable;

Not sure about this one, is the explicit 'input-enable' actually needed here?

Maybe not, will test it once after I remove it


+		bias-disable;
+	};
+
+	ts_int_l: ts-int-l {
+		pins = "gpio55";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	ts_reset_l: ts-reset-l {
+		pins = "gpio54";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;

As per my comment on "[3/4] arm64: dts: qcom: sc7280: Define EC and H1 nodes" it
seems setting the drive strength to 2 isn't necessary, since that's the default.

right I'll remove it, thanks



--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux