On Fri 29 Oct 17:03 PDT 2021, quic_vamslank@xxxxxxxxxxx wrote: > From: Vamsi Krishna Lanka <quic_vamslank@xxxxxxxxxxx> > > Add device tree binding Documentation details for Qualcomm SDX65 > pinctrl driver. > > Signed-off-by: Vamsi Krishna Lanka <quic_vamslank@xxxxxxxxxxx> > --- > .../bindings/pinctrl/qcom,sdx65-pinctrl.yaml | 195 +++++++++++++++++++++ > 1 file changed, 195 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml > > diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml > new file mode 100644 > index 0000000..589ff2f > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml > @@ -0,0 +1,195 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pinctrl/qcom,sdx65-pinctrl.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm Technologies, Inc. SDX65 TLMM block > + > +maintainers: > + - Vamsi krishna Lanka <quic_vamslank@xxxxxxxxxxx> > + > +description: | Nit. The '|' here denotes that the formatting of the description should be maintaied, there's no need for that so you can safely omit it. > + This binding describes the Top Level Mode Multiplexer block found in the > + SDX65 platform. > + > +properties: > + compatible: > + const: qcom,sdx65-tlmm > + > + reg: > + description: Specifies the base address and size of the TLMM register space > + maxItems: 1 > + > + interrupts: > + description: Specifies the TLMM summary IRQ > + maxItems: 1 > + > + interrupt-controller: true > + > + '#interrupt-cells': > + description: Specifies the PIN numbers and Flags, as defined in > + include/dt-bindings/interrupt-controller/irq.h > + const: 2 > + > + gpio-controller: true > + > + '#gpio-cells': > + description: Specifying the pin number and flags, as defined in > + include/dt-bindings/gpio/gpio.h > + const: 2 > + > + gpio-ranges: > + maxItems: 1 > + > + gpio-reserved-ranges: > + maxItems: 1 > + > +#PIN CONFIGURATION NODES > +patternProperties: > +'-state$': > + oneOf: > + - $ref: "#/$defs/qcom-sdx65-tlmm-state" > + - patternProperties: > + ".*": > + $ref: "#/$defs/qcom-sdx65-tlmm-state" > +'$defs': > + qcom-sdx65-tlmm-state: > + type: object > + description: > + Pinctrl node's client devices use subnodes for desired pin configuration. > + Client device subnodes use below standard properties. > + $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" > + > + properties: > + pins: > + description: > + List of gpio pins affected by the properties specified in this subnode. > + items: > + oneOf: > + - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9])$" > + - enum: [ ufs_reset, sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, sdc1_rclk ] > + minItems: 1 > + maxItems: 150 > + > + function: > + description: > + Specify the alternative function to be configured for the specified > + pins. Functions are only valid for gpio pins. > + enum: [ blsp_uart1, blsp_spi1, blsp_i2c1, blsp_uim1, atest_tsens, > + bimc_dte1, dac_calib0, blsp_spi8, blsp_uart8, blsp_uim8, > + qdss_cti_trig_out_b, bimc_dte0, dac_calib1, qdss_cti_trig_in_b, > + dac_calib2, atest_tsens2, atest_usb1, blsp_spi10, blsp_uart10, > + blsp_uim10, atest_bbrx1, atest_usb13, atest_bbrx0, atest_usb12, > + mdp_vsync, edp_lcd, blsp_i2c10, atest_gpsadc1, atest_usb11, > + atest_gpsadc0, edp_hot, atest_usb10, m_voc, dac_gpio, atest_char, > + cam_mclk, pll_bypassnl, qdss_stm7, blsp_i2c8, qdss_tracedata_b, > + pll_reset, qdss_stm6, qdss_stm5, qdss_stm4, atest_usb2, cci_i2c, > + qdss_stm3, dac_calib3, atest_usb23, atest_char3, dac_calib4, > + qdss_stm2, atest_usb22, atest_char2, qdss_stm1, dac_calib5, > + atest_usb21, atest_char1, dbg_out, qdss_stm0, dac_calib6, > + atest_usb20, atest_char0, dac_calib10, qdss_stm10, > + qdss_cti_trig_in_a, cci_timer4, blsp_spi6, blsp_uart6, blsp_uim6, > + blsp2_spi, qdss_stm9, qdss_cti_trig_out_a, dac_calib11, > + qdss_stm8, cci_timer0, qdss_stm13, dac_calib7, cci_timer1, > + qdss_stm12, dac_calib8, cci_timer2, blsp1_spi, qdss_stm11, > + dac_calib9, cci_timer3, cci_async, dac_calib12, blsp_i2c6, > + qdss_tracectl_a, dac_calib13, qdss_traceclk_a, dac_calib14, > + dac_calib15, hdmi_rcv, dac_calib16, hdmi_cec, pwr_modem, > + dac_calib17, hdmi_ddc, pwr_nav, dac_calib18, pwr_crypto, > + dac_calib19, hdmi_hot, dac_calib20, dac_calib21, pci_e0, > + dac_calib22, dac_calib23, dac_calib24, tsif1_sync, dac_calib25, > + sd_write, tsif1_error, blsp_spi2, blsp_uart2, blsp_uim2, > + qdss_cti, blsp_i2c2, blsp_spi3, blsp_uart3, blsp_uim3, blsp_i2c3, > + uim3, blsp_spi9, blsp_uart9, blsp_uim9, blsp10_spi, blsp_i2c9, > + blsp_spi7, blsp_uart7, blsp_uim7, qdss_tracedata_a, blsp_i2c7, > + qua_mi2s, gcc_gp1_clk_a, ssc_irq, uim4, blsp_spi11, blsp_uart11, > + blsp_uim11, gcc_gp2_clk_a, gcc_gp3_clk_a, blsp_i2c11, cri_trng0, > + cri_trng1, cri_trng, qdss_stm18, pri_mi2s, qdss_stm17, blsp_spi4, > + blsp_uart4, blsp_uim4, qdss_stm16, qdss_stm15, blsp_i2c4, > + qdss_stm14, dac_calib26, spkr_i2s, audio_ref, lpass_slimbus, > + isense_dbg, tsense_pwm1, tsense_pwm2, btfm_slimbus, ter_mi2s, > + qdss_stm22, qdss_stm21, qdss_stm20, qdss_stm19, gcc_gp1_clk_b, > + sec_mi2s, blsp_spi5, blsp_uart5, blsp_uim5, gcc_gp2_clk_b, > + gcc_gp3_clk_b, blsp_i2c5, blsp_spi12, blsp_uart12, blsp_uim12, > + qdss_stm25, qdss_stm31, blsp_i2c12, qdss_stm30, qdss_stm29, > + tsif1_clk, qdss_stm28, tsif1_en, tsif1_data, sdc4_cmd, qdss_stm27, > + qdss_traceclk_b, tsif2_error, sdc43, vfr_1, qdss_stm26, tsif2_clk, > + sdc4_clk, qdss_stm24, tsif2_en, sdc42, qdss_stm23, qdss_tracectl_b, > + sd_card, tsif2_data, sdc41, tsif2_sync, sdc40, mdp_vsync_p_b, > + ldo_en, mdp_vsync_s_b, ldo_update, blsp11_uart_tx_b, blsp11_uart_rx_b, > + blsp11_i2c_sda_b, prng_rosc, blsp11_i2c_scl_b, uim2, uim1, uim_batt, > + pci_e2, pa_indicator, adsp_ext, ddr_bist, qdss_tracedata_11, > + qdss_tracedata_12, modem_tsync, nav_dr, nav_pps, pci_e1, gsm_tx, > + qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3, > + gpio ] > + > + drive-strength: > + enum: [2, 4, 6, 8, 10, 12, 14, 16] > + default: 2 > + description: > + Selects the drive strength for the specified pins, in mA. > + > + bias-pull-down: true > + > + bias-pull-up: true > + > + bias-disable: true > + > + output-high: true > + > + output-low: true > + > + required: > + - pins > + - function > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - interrupt-controller > + - '#interrupt-cells' > + - gpio-controller > + - '#gpio-cells' > + - gpio-ranges > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + tlmm: pinctrl@f100000 { > + compatible = "qcom,sdx65-tlmm"; > + reg = <0x03000000 0xdc2000>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&tlmm 0 0 109>; > + interrupt-controller; > + #interrupt-cells = <2>; > + interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>; > + > + serial-pins { You define the child nodes as: patternProperties: '-state$': Hence this pinctrl state needs to end with the string "-state". With that fixed, please rebase on v5.16-rc1 and add my Reviewed-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx> Regards, Bjorn > + pins = "gpio8", "gpio9"; > + function = "blsp_uart3"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + uart-w-subnodes-state { > + rx { > + pins = "gpio4"; > + function = "blsp_uart1"; > + bias-pull-up; > + }; > + > + tx { > + pins = "gpio5"; > + function = "blsp_uart1"; > + bias-disable; > + }; > + }; > + }; > +... > -- > 2.7.4 >
