Re: [PATCH] media: venus: Synchronize probe() between venus_core and enc/dec

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Oct 25, 2021 at 7:44 AM Tadeusz Struk <tadeusz.struk@xxxxxxxxxx> wrote:
>
> Venus video encode/decode hardware driver consists of three modules.
> The parent module venus-core, and two sub modules venus-enc and venus-dec.
> The venus-core module allocates a common structure that is used by the
> enc/dec modules, loads the firmware, and performs some common hardware
> initialization. Since the three modules are loaded one after the other,
> and their probe functions can run in parallel it is possible that
> the venc_probe and vdec_probe functions can finish before the core
> venus_probe function, which then can fail when, for example it
> fails to load the firmware. In this case the subsequent call to venc_open
> causes an Oops as it tries to dereference already uninitialized structures
> through dev->parent and the system crashes in __pm_runtime_resume() as in
> the trace below:
>
> [   26.064835][  T485] Internal error: Oops: 96000006 [#1] PREEMPT SMP
> [   26.270914][  T485] Hardware name: Thundercomm Dragonboard 845c (DT)
> [   26.285019][  T485] pc : __pm_runtime_resume+0x34/0x178
> [   26.286374][  T213] lt9611 10-003b: hdmi cable connected
> [   26.290285][  T485] lr : venc_open+0xc0/0x278 [venus_enc]
> [   26.290326][  T485] Call trace:
> [   26.290328][  T485]  __pm_runtime_resume+0x34/0x178
> [   26.290330][  T485]  venc_open+0xc0/0x278 [venus_enc]
> [   26.290335][  T485]  v4l2_open+0x184/0x294
> [   26.290340][  T485]  chrdev_open+0x468/0x5c8
> [   26.290344][  T485]  do_dentry_open+0x260/0x54c
> [   26.290349][  T485]  path_openat+0xbe8/0xd5c
> [   26.290352][  T485]  do_filp_open+0xb8/0x168
> [   26.290354][  T485]  do_sys_openat2+0xa4/0x1e8
> [   26.290357][  T485]  __arm64_compat_sys_openat+0x70/0x9c
> [   26.290359][  T485]  invoke_syscall+0x60/0x170
> [   26.290363][  T485]  el0_svc_common+0xb8/0xf8
> [   26.290365][  T485]  do_el0_svc_compat+0x20/0x30
> [   26.290367][  T485]  el0_svc_compat+0x24/0x84
> [   26.290372][  T485]  el0t_32_sync_handler+0x7c/0xbc
> [   26.290374][  T485]  el0t_32_sync+0x1b8/0x1bc
> [   26.290381][  T485] ---[ end trace 04ca7c088b4c1a9c ]---
> [   26.290383][  T485] Kernel panic - not syncing: Oops: Fatal exception
>
> This can be fixed by synchronizing the three probe functions and
> only allowing the venc_probe() and vdec_probe() to pass when venus_probe()
> returns success.
>
> Signed-off-by: Tadeusz Struk <tadeusz.struk@xxxxxxxxxx>


Hey Tadeusz
  Thanks so much for sending this out, I definitely would like to see
these crashes sorted!

Unfortunately this patch causes some odd behavior when I use it with a
modular config.  The display does not start up and trying to reboot
the board ends up with it hanging instead of rebooting.

And booting with this patch in my non-modular config, it just seems to
get stuck during bootup (I suspect waiting on firmware that's not yet
mounted?).

I've got to run right now, but I'll try to help debug this down further.

thanks
-john



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux