Hi Carl and Kalle, On Thu, 23 Sept 2021 at 11:26, Carl Huang <cjhuang@xxxxxxxxxxxxxx> wrote: > > On 2021-09-23 16:59, Manivannan Sadhasivam wrote: > > On Thu, Sep 23, 2021 at 04:34:43PM +0800, Carl Huang wrote: > >> On 2021-09-17 01:19, Manivannan Sadhasivam wrote: > >> > On Thu, Sep 16, 2021 at 07:42:02PM +0300, Kalle Valo wrote: > >> > > Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx> writes: > >> > > > >> > > > On Thu, Sep 16, 2021 at 01:18:22PM +0200, Loic Poulain wrote: > >> > > >> Le jeu. 16 sept. 2021 à 13:12, Manivannan Sadhasivam < > >> > > >> manivannan.sadhasivam@xxxxxxxxxx> a écrit : > >> > > >> > >> > > > > >> > > > [...] > >> > > > > >> > > >> > If things seems to work fine without that patch, then it implies that > >> > > >> > setting M0 > >> > > >> > state works during resume. I think we should just revert that patch. > >> > > >> > > >> > > >> > Loic, did that patch fix any issue for you or it was a cosmetic fix only? > >> > > >> > >> > > >> > >> > > >> It fixes sdx modem resuming issue, without that we don’t know modem needs > >> > > >> to be reinitialized. > >> > > >> > >> > > > > >> > > > Okay. Then in that case, the recovery mechanism has to be added to the ath11k > >> > > > MHI controller. > >> > > > >> > > What does that mean in practise, do you have any pointers or > >> > > examples? I > >> > > have no clue what you are proposing :) > >> > > > >> > > >> > Take a look at the mhi_pci_recovery_work() function below: > >> > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/bus/mhi/pci_generic.c#n610 > >> > > >> > You need to implement something similar that basically powers up the MHI > >> > endpoint (QCA6390) in case pm_resume() fails. At minimum, you need to > >> > call > >> > below functions: > >> > > >> > # Check if the device is powered on. If yes, then power it down to bring > >> > it back > >> > mhi_power_down() > >> > mhi_unprepare_after_power_down() > >> > > >> > # Power up the device > >> > mhi_prepare_for_power_up() > >> > mhi_sync_power_up() > >> > > >> > This implies that the WLAN device has been powered off during suspend, > >> > so the > >> > resume fails and we are bringing the device back to working state. > >> > > >> This is fine for platform which doesn't provide power supply during > >> suspend. > >> But NUC has power supply in suspend state. > > > > If NUC retains power supply during suspend then it should work with > > that commit. > > During resume, the device is expected to be in M3 state and that's what > > the > > commit verifies. > > > > If the device is in a different state, then most likely the device have > > power > > cycled. > > > But the tricky thing here is that upstream QCA6390 doesn't have recovery > mechanism to download > firmware again, so QCA6390 has no way to work after a power cycle. Maybe a simple quick-fix would be to add a 'force' parameter to the mhi resume function and discard state testing in case it is forced, that would allow both ath11k and modem to work for now. Then investigating what happens on ath11k side. Thoughts? Regards, Loic
