Re: [PATCH v6 2/4] arm64: dts: qcom: sc7280: Add PCIe and PHY related nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Quoting Prasad Malisetty (2021-09-09 10:40:43)
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 53a21d0..422c112 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -7,6 +7,7 @@
>
>  #include <dt-bindings/clock/qcom,gcc-sc7280.h>
>  #include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/interconnect/qcom,sc7280.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/mailbox/qcom-ipcc.h>
> @@ -586,6 +587,119 @@
>                         qcom,bcm-voters = <&apps_bcm_voter>;
>                 };
>
> +               pcie1: pci@1c08000 {
> +                       compatible = "qcom,pcie-sc7280", "qcom,pcie-sm8250";

Can you please drop pcie-sm8250?

> +                       reg = <0 0x01c08000 0 0x3000>,
> +                             <0 0x40000000 0 0xf1d>,
> +                             <0 0x40000f20 0 0xa8>,
> +                             <0 0x40001000 0 0x1000>,
> +                             <0 0x40100000 0 0x100000>;
> +
> +                       reg-names = "parf", "dbi", "elbi", "atu", "config";
> +                       device_type = "pci";
> +                       linux,pci-domain = <1>;
> +                       bus-range = <0x00 0xff>;
> +                       num-lanes = <2>;
> +                       pipe-clk-source-switch;

I thought this property was going away?

> +
> +                       #address-cells = <3>;
> +                       #size-cells = <2>;
> +
> +                       ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
> +                                <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
> +
> +                       interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
> +                       interrupt-names = "msi";
> +                       #interrupt-cells = <1>;
> +                       interrupt-map-mask = <0 0 0 0x7>;
> +                       interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
> +                                       <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
> +                                       <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>,
> +                                       <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>;
> +
> +                       clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
> +                                <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
> +                                <&pcie1_lane 0>,
> +                                <&rpmhcc RPMH_CXO_CLK>,
> +                                <&gcc GCC_PCIE_1_AUX_CLK>,
> +                                <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> +                                <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
> +                                <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
> +                                <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
> +                                <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
> +                                <&gcc GCC_DDRSS_PCIE_SF_CLK>;
> +
> +                       clock-names = "pipe",
> +                                     "pipe_mux",
> +                                     "phy_pipe",
> +                                     "ref",
> +                                     "aux",
> +                                     "cfg",
> +                                     "bus_master",
> +                                     "bus_slave",
> +                                     "slave_q2a",
> +                                     "tbu",
> +                                     "ddrss_sf_tbu";
> +
> +                       assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
> +                       assigned-clock-rates = <19200000>;
> +
> +                       resets = <&gcc GCC_PCIE_1_BCR>;
> +                       reset-names = "pci";
> +
> +                       power-domains = <&gcc GCC_PCIE_1_GDSC>;
> +
> +                       phys = <&pcie1_lane>;
> +                       phy-names = "pciephy";
> +
> +                       perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;

This should move to the board file because it's a plain old gpio.

> +                       pinctrl-names = "default";
> +                       pinctrl-0 = <&pcie1_default_state>;
> +
> +                       iommus = <&apps_smmu 0x1c80 0x1>;
> +
> +                       iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
> +                                   <0x100 &apps_smmu 0x1c81 0x1>;
> +
> +                       status = "disabled";
> +               };
> +
> +               pcie1_phy: phy@1c0e000 {
> +                       compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy";

sc7280-qmp-gen3x2-pcie-phy?

> +                       reg = <0 0x01c0e000 0 0x1c0>;
> +                       #address-cells = <2>;
> +                       #size-cells = <2>;
> +                       ranges;
> +                       clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
> +                                <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> +                                <&gcc GCC_PCIE_CLKREF_EN>,
> +                                <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
> +                       clock-names = "aux", "cfg_ahb", "ref", "refgen";
> +
> +                       resets = <&gcc GCC_PCIE_1_PHY_BCR>;
> +                       reset-names = "phy";
> +
> +                       assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
> +                       assigned-clock-rates = <100000000>;
> +
> +                       status = "disabled";
> +
> +                       pcie1_lane: lanes@1c0e200 {
> +                               reg = <0 0x01c0e200 0 0x170>,
> +                                     <0 0x01c0e400 0 0x200>,
> +                                     <0 0x01c0ea00 0 0x1f0>,
> +                                     <0 0x01c0e600 0 0x170>,
> +                                     <0 0x01c0e800 0 0x200>,
> +                                     <0 0x01c0ee00 0 0xf4>;
> +                               clocks = <&rpmhcc RPMH_CXO_CLK>;
> +                               clock-names = "pipe0";
> +
> +                               #phy-cells = <0>;
> +                               #clock-cells = <1>;
> +                               clock-output-names = "pcie_1_pipe_clk";
> +                       };
> +               };
> +
>                 ipa: ipa@1e40000 {
>                         compatible = "qcom,sc7280-ipa";
>
> @@ -1598,6 +1712,13 @@
>                                         bias-bus-hold;
>                                 };
>                         };
> +
> +                       pcie1_default_state: pcie1-default-state {
> +                               clkreq {

Drop clkreq node and just put the pin and function directly inside
please.

> +                                       pins = "gpio79";
> +                                       function = "pcie1_clkreqn";
> +                               };
> +                       };
>                 };
>
>                 apps_smmu: iommu@15000000 {



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux