Re: [PATCH v7 0/6] clk: qcom: use power-domain for sm8250's clock controllers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, 29 Aug 2021 at 17:47, Dmitry Baryshkov
<dmitry.baryshkov@xxxxxxxxxx> wrote:
>
> On SM8250 both the display and video clock controllers are powered up by
> the MMCX power domain. Handle this by linking clock controllers to the
> proper power domain, and using runtime power management to enable and
> disable the MMCX power domain.
>
> Dependencies:
> https://lore.kernel.org/linux-pm/1628767642-4008-1-git-send-email-rnayak@xxxxxxxxxxxxxx/
> (pending inclusion into 5.15)

I think I already reviewed v6, but perhaps you made some bigger
changes. Anyway, feel free to add, for the series:

Reviewed-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>

Kind regards
Uffe

>
> Changes since v6:
>  - Dropped dependency on Bjorn's patches
>  - Restored required-opps properties
>  - Held pm device state while gdsc is powered on, removing dependency on
>    genpd's power_on() powering the domain into required state.
>
> Changes since v5:
>  - Dropped devm_pm_runtime_enable callback to remove extra dependency
>
> Changes since v4:
>  - Dropped pm_runtime handling from drivers/clk/qcom/common.c Moved the
>    code into dispcc-sm8250.c and videocc-sm8250.c
>
> Changes since v3:
>  - Wrap gdsc_enable/gdsc_disable into pm_runtime_get/put calls rather
>    than calling pm_runtime_get in gdsc_enabled and _put in gdsc_disable
>  - Squash gdsc patches together to remove possible dependencies between
>    two patches.
>
> Changes since v2:
>  - Move pm_runtime calls from generic genpd code to the gdsc code for
>    now (as suggested by Ulf & Bjorn)
>
> Changes since v1:
>  - Rebase on top of Bjorn's patches, removing the need for setting
>    performance state directly.
>  - Move runtime PM calls from GDSC code to generic genpd code.
>  - Always call pm_runtime_enable in the Qualcomm generic clock
>    controller code.
>  - Register GDSC power domains as subdomains of the domain powering the
>    clock controller if there is one.
>
> ----------------------------------------------------------------
> Dmitry Baryshkov (8):
>       dt-bindings: clock: qcom,dispcc-sm8x50: add mmcx power domain
>       dt-bindings: clock: qcom,videocc: add mmcx power domain
>       clk: qcom: dispcc-sm8250: use runtime PM for the clock controller
>       clk: qcom: videocc-sm8250: use runtime PM for the clock controller
>       clk: qcom: gdsc: enable optional power domain support
>       arm64: dts: qcom: sm8250: remove mmcx regulator
>       clk: qcom: dispcc-sm8250: stop using mmcx regulator
>       clk: qcom: videocc-sm8250: stop using mmcx regulator
>
>  .../bindings/clock/qcom,dispcc-sm8x50.yaml         | 13 ++++++
>  .../devicetree/bindings/clock/qcom,videocc.yaml    | 13 ++++++
>  arch/arm64/boot/dts/qcom/sm8250.dtsi               | 13 ++----
>  drivers/clk/qcom/dispcc-sm8250.c                   | 28 ++++++++++--
>  drivers/clk/qcom/gdsc.c                            | 51 ++++++++++++++++++++--
>  drivers/clk/qcom/gdsc.h                            |  2 +
>  drivers/clk/qcom/videocc-sm8250.c                  | 31 ++++++++++---
>  7 files changed, 130 insertions(+), 21 deletions(-)
>
>
>



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux