On 2021-08-23 11:43 AM, Jeffrey Hugo wrote:
On 2/24/2021 4:23 PM, Bhaumik Bhatt wrote:
In current design, whenever the BHI interrupt is fired, the
execution environment is updated. This can cause race conditions
and impede ongoing power up/down processing. For example, if a
power down is in progress, MHI host updates to a local "disabled"
execution environment. If a BHI interrupt fires later, that value
gets replaced with one from the BHI EE register. This impacts the
controller as it does not expect multiple RDDM execution
environment change status callbacks as an example. Another issue
would be that the device can enter mission mode and the execution
environment is updated, while device creation for SBL channels is
still going on due to slower PM state worker thread run, leading
to multiple attempts at opening the same channel.
Ensure that EE changes are handled only from appropriate places
and occur one after another and handle only PBL modes or RDDM EE
changes as critical events directly from the interrupt handler.
Simplify handling by waiting for SYS ERROR before handling RDDM.
This also makes sure that we use the correct execution environment
to notify the controller driver when the device resets to one of
the PBL execution environments.
Signed-off-by: Bhaumik Bhatt <bbhatt@xxxxxxxxxxxxxx>
<snip>
@@ -452,27 +451,30 @@ irqreturn_t mhi_intvec_threaded_handler(int
irq_number, void *priv)
}
write_unlock_irq(&mhi_cntrl->pm_lock);
- /* If device supports RDDM don't bother processing SYS error */
- if (mhi_cntrl->rddm_image) {
- /* host may be performing a device power down already */
- if (!mhi_is_active(mhi_cntrl))
- goto exit_intvec;
+ if (pm_state != MHI_PM_SYS_ERR_DETECT || ee == mhi_cntrl->ee)
+ goto exit_intvec;
- if (mhi_cntrl->ee == MHI_EE_RDDM && mhi_cntrl->ee != ee) {
+ switch (ee) {
+ case MHI_EE_RDDM:
+ /* proceed if power down is not already in progress */
+ if (mhi_cntrl->rddm_image && mhi_is_active(mhi_cntrl)) {
mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_EE_RDDM);
+ mhi_cntrl->ee = ee;
wake_up_all(&mhi_cntrl->state_event);
}
- goto exit_intvec;
- }
-
- if (pm_state == MHI_PM_SYS_ERR_DETECT) {
+ break;
+ case MHI_EE_PBL:
+ case MHI_EE_EDL:
+ case MHI_EE_PTHRU:
+ mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_FATAL_ERROR);
+ mhi_cntrl->ee = ee;
wake_up_all(&mhi_cntrl->state_event);
-
- /* For fatal errors, we let controller decide next step */
- if (MHI_IN_PBL(ee))
- mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_FATAL_ERROR);
- else
- mhi_pm_sys_err_handler(mhi_cntrl);
+ mhi_pm_sys_err_handler(mhi_cntrl);
+ break;
+ default:
+ wake_up_all(&mhi_cntrl->state_event);
+ mhi_pm_sys_err_handler(mhi_cntrl);
+ break;
}
Bhaumik, can you explain the above change? Before this patch (which
is now committed), if there was a fatal error, the controller was
notified (MHI_CB_FATAL_ERROR) and it decided all action. After this
patch, the controller is notified, but also the core attempts to
handle the syserr.
This is a change in behavior, and seems to make a mess of the
controller, and possibly the core fighting each other.
Specifically, I'm rebasing the AIC100 driver onto 5.13, which has this
change, and I'm seeing a serious regression. I'm thinking that for
the PBL/EDL/PTHRU case, mhi_pm_sys_err_handler() should not be called.
Thoughts?
I see. We use this heavily for entry to EDL use-cases.
We do require the mhi_pm_sys_err_handler() to be called in those cases
as any entry to PBL/EDL means there is need to clean-up MHI host and
notify all
its clients.
We include PTHRU in here because its a SYS ERROR in PBL modes.
Premise being the controller should not be in that business of doing any
of
the clean-up that is responsibility of the core driver. We're using this
feature
set to ensure controller is only notified.
What does AIC100 do on fatal error that you run in to issues? I don't
think
any of the other controllers do anything other than disabling runtime PM
since
device is down. Maybe there's some room for improvement.
Thanks,
Bhaumik
---
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum,
a Linux Foundation Collaborative Project
