In some configurations, the BAM DMA controller is set up by a remote
processor and the local processor can simply start making use of it
without setting up the BAM. This is already supported using the
"qcom,controlled-remotely" property.
However, for some reason another possible configuration is that the
remote processor is responsible for powering up the BAM, but we are
still responsible for initializing it (e.g. resetting it etc).
This configuration is quite challenging to handle properly because
the power control is handled through separate channels
(e.g. device-specific SMSM interrupts / smem-states). Great care
must be taken to ensure the BAM registers are not accessed while
the BAM is power-collapsed since this results in a bus stall.
Attempt to support this configuration with minimal device-specific
code in the bam_dma driver by tracking the number of requested
channels. Consumers of DMA channels are responsible to only request
DMA channels when the BAM was powered on by the remote processor,
and to release them before the BAM is power-collapsed.
When the first channel is requested the BAM is initialized (reset)
and it is also put into reset when the last channel was released.
Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
---
NOTE: This is *not* a compile-time requirement for the BAM-DMUX driver
so this could also go through the dmaengine tree.
I tried to come up with other solutions for this situation, but this
is the cleanest I came up with so far. The main advantage is that
it keeps the bam_dma driver generic and fairly simple. The main
disadvantage might be that there is some overhead when the DMA channels
are repeatedly requested and released (the BAM-DMUX driver uses
PM runtime to autosuspend after 1 second of inactivity).
Some alternative ideas (but I'm not sure how they would work exactly):
- Have some dmaengine_*() operation to make the bam_dma driver aware
that the BAM is power-collapsed (instead of requesting/releasing
the channels every time).
- Give the BAM-DMUX power control IRQ to bam_dma so it knows when
the BAM is power-collapsed or not.
- Perhaps even give the smem-state to bam_dma so it could request
powering on the BAM itself. This would be quite strange though,
since bam_dma already uses runtime PM but differently (only active
during register writes, not necessarily active during transfers).
Note however that the power control of BAM-DMUX also involves
queuing RX buffers so there would be much more coordination
needed between bam_dma and bam-dmux.
All in all, I think the solution in this patch is still the cleanest
approach so far.
---
drivers/dma/qcom/bam_dma.c | 88 ++++++++++++++++++++++++--------------
1 file changed, 56 insertions(+), 32 deletions(-)
diff --git a/drivers/dma/qcom/bam_dma.c b/drivers/dma/qcom/bam_dma.c
index c8a77b428b52..8bf6c50bda73 100644
--- a/drivers/dma/qcom/bam_dma.c
+++ b/drivers/dma/qcom/bam_dma.c
@@ -388,6 +388,8 @@ struct bam_device {
/* execution environment ID, from DT */
u32 ee;
bool controlled_remotely;
+ bool remote_power_collapse;
+ u32 active_channels;
const struct reg_offset_data *layout;
@@ -415,6 +417,44 @@ static inline void __iomem *bam_addr(struct bam_device *bdev, u32 pipe,
r.ee_mult * bdev->ee;
}
+/**
+ * bam_reset - reset and initialize BAM registers
+ * @bdev: bam device
+ */
+static void bam_reset(struct bam_device *bdev)
+{
+ u32 val;
+
+ /* s/w reset bam */
+ /* after reset all pipes are disabled and idle */
+ val = readl_relaxed(bam_addr(bdev, 0, BAM_CTRL));
+ val |= BAM_SW_RST;
+ writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
+ val &= ~BAM_SW_RST;
+ writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
+
+ /* make sure previous stores are visible before enabling BAM */
+ wmb();
+
+ /* enable bam */
+ val |= BAM_EN;
+ writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
+
+ /* set descriptor threshhold, start with 4 bytes */
+ writel_relaxed(DEFAULT_CNT_THRSHLD,
+ bam_addr(bdev, 0, BAM_DESC_CNT_TRSHLD));
+
+ /* Enable default set of h/w workarounds, ie all except BAM_FULL_PIPE */
+ writel_relaxed(BAM_CNFG_BITS_DEFAULT, bam_addr(bdev, 0, BAM_CNFG_BITS));
+
+ /* enable irqs for errors */
+ writel_relaxed(BAM_ERROR_EN | BAM_HRESP_ERR_EN,
+ bam_addr(bdev, 0, BAM_IRQ_EN));
+
+ /* unmask global bam interrupt */
+ writel_relaxed(BAM_IRQ_MSK, bam_addr(bdev, 0, BAM_IRQ_SRCS_MSK_EE));
+}
+
/**
* bam_reset_channel - Reset individual BAM DMA channel
* @bchan: bam channel
@@ -512,6 +552,9 @@ static int bam_alloc_chan(struct dma_chan *chan)
return -ENOMEM;
}
+ if (bdev->active_channels++ == 0 && bdev->remote_power_collapse)
+ bam_reset(bdev);
+
return 0;
}
@@ -565,6 +608,13 @@ static void bam_free_chan(struct dma_chan *chan)
/* disable irq */
writel_relaxed(0, bam_addr(bdev, bchan->id, BAM_P_IRQ_EN));
+ if (--bdev->active_channels == 0 && bdev->remote_power_collapse) {
+ /* s/w reset bam */
+ val = readl_relaxed(bam_addr(bdev, 0, BAM_CTRL));
+ val |= BAM_SW_RST;
+ writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
+ }
+
err:
pm_runtime_mark_last_busy(bdev->dev);
pm_runtime_put_autosuspend(bdev->dev);
@@ -1164,38 +1214,10 @@ static int bam_init(struct bam_device *bdev)
bdev->num_channels = val & BAM_NUM_PIPES_MASK;
}
- if (bdev->controlled_remotely)
+ if (bdev->controlled_remotely || bdev->remote_power_collapse)
return 0;
- /* s/w reset bam */
- /* after reset all pipes are disabled and idle */
- val = readl_relaxed(bam_addr(bdev, 0, BAM_CTRL));
- val |= BAM_SW_RST;
- writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
- val &= ~BAM_SW_RST;
- writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
-
- /* make sure previous stores are visible before enabling BAM */
- wmb();
-
- /* enable bam */
- val |= BAM_EN;
- writel_relaxed(val, bam_addr(bdev, 0, BAM_CTRL));
-
- /* set descriptor threshhold, start with 4 bytes */
- writel_relaxed(DEFAULT_CNT_THRSHLD,
- bam_addr(bdev, 0, BAM_DESC_CNT_TRSHLD));
-
- /* Enable default set of h/w workarounds, ie all except BAM_FULL_PIPE */
- writel_relaxed(BAM_CNFG_BITS_DEFAULT, bam_addr(bdev, 0, BAM_CNFG_BITS));
-
- /* enable irqs for errors */
- writel_relaxed(BAM_ERROR_EN | BAM_HRESP_ERR_EN,
- bam_addr(bdev, 0, BAM_IRQ_EN));
-
- /* unmask global bam interrupt */
- writel_relaxed(BAM_IRQ_MSK, bam_addr(bdev, 0, BAM_IRQ_SRCS_MSK_EE));
-
+ bam_reset(bdev);
return 0;
}
@@ -1257,8 +1279,10 @@ static int bam_dma_probe(struct platform_device *pdev)
bdev->controlled_remotely = of_property_read_bool(pdev->dev.of_node,
"qcom,controlled-remotely");
+ bdev->remote_power_collapse = of_property_read_bool(pdev->dev.of_node,
+ "qcom,remote-power-collapse");
- if (bdev->controlled_remotely) {
+ if (bdev->controlled_remotely || bdev->remote_power_collapse) {
ret = of_property_read_u32(pdev->dev.of_node, "num-channels",
&bdev->num_channels);
if (ret)
@@ -1270,7 +1294,7 @@ static int bam_dma_probe(struct platform_device *pdev)
dev_err(bdev->dev, "num-ees unspecified in dt\n");
}
- if (bdev->controlled_remotely)
+ if (bdev->controlled_remotely || bdev->remote_power_collapse)
bdev->bamclk = devm_clk_get_optional(bdev->dev, "bam_clk");
else
bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk");
--
2.32.0
