Whenever SDHC run at clock rate 50MHZ or below, the hardware data
timeout value will be 21.47secs, which is approx. 22secs and we have
a current software timeout value as 10secs. We have to set software
timeout value more than the hardware data timeout value to avioid seeing
the below register dumps.
[ 332.953670] mmc2: Timeout waiting for hardware interrupt.
[ 332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 332.966450] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00007202
[ 332.973256] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001
[ 332.980054] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000027
[ 332.986864] mmc2: sdhci: Present: 0x01f801f6 | Host ctl: 0x0000001f
[ 332.993671] mmc2: sdhci: Power: 0x00000001 | Blk gap: 0x00000000
[ 333.000583] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x00000007
[ 333.007386] mmc2: sdhci: Timeout: 0x0000000e | Int stat: 0x00000000
[ 333.014182] mmc2: sdhci: Int enab: 0x03ff100b | Sig enab: 0x03ff100b
[ 333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[ 333.027771] mmc2: sdhci: Caps: 0x322dc8b2 | Caps_1: 0x0000808f
[ 333.034561] mmc2: sdhci: Cmd: 0x0000183a | Max curr: 0x00000000
[ 333.041359] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x00000000
[ 333.048157] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 333.054945] mmc2: sdhci: Host ctl2: 0x00000000
[ 333.059657] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr:
0x0000000ffffff218
[ 333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP
-----------
[ 333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg:
0x6000642c | DLL cfg2: 0x0020a000
[ 333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl:
0x00000000 | DDR cfg: 0x80040873
[ 333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 :
0xf88218a8 Vndr func3: 0x02626040
[ 333.102371] mmc2: sdhci: ============================================
So, set software timeout value more than hardware timeout value.
Signed-off-by: Shaik Sajida Bhanu <sbhanu@xxxxxxxxxxxxxx>
---
Changes since V2:
- Updated 22 with 22LL to avoid compiler warning as suggested by
Adrian Hunter.
- Added a check to update software data timeout value if its value is
less than the calculated hardware data timeout value as suggested
by Veerabhadrarao Badiganti.
Changes since V1:
- Moved software data timeout update part to qcom specific file
as suggested by Veerabhadrarao Badiganti.
---
drivers/mmc/host/sdhci-msm.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index e44b7a6..64fb85e 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -2089,6 +2089,23 @@ static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
sdhci_cqe_disable(mmc, recovery);
}
+static void sdhci_msm_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
+{
+
+ u32 count, start = 15;
+
+ __sdhci_set_timeout(host, cmd);
+ count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL);
+ /*
+ * Update software timeout value if its value is less than hardware data
+ * timeout value. Qcom SoC hardware data timeout value was calculated
+ * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock.
+ */
+ if (cmd && cmd->data && host->clock > 400000 && host->clock <= 50000000
+ && ((1 << (count + start)) > (10 * host->clock)))
+ host->data_timeout = 22LL * NSEC_PER_SEC;
+}
+
static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
.enable = sdhci_msm_cqe_enable,
.disable = sdhci_msm_cqe_disable,
@@ -2438,6 +2455,7 @@ static const struct sdhci_ops sdhci_msm_ops = {
.irq = sdhci_msm_cqe_irq,
.dump_vendor_regs = sdhci_msm_dump_vendor_regs,
.set_power = sdhci_set_power_noreg,
+ .set_timeout = sdhci_msm_set_timeout,
};
static const struct sdhci_pltfm_data sdhci_msm_pdata = {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
