Changes in V11:
- Added a DWC3 controller revision check to use a different calculation, based
on Ferry's testing.
- Removed descriptor loop in configfs, and utilize the fact that the ep->claimed
parameter is still valid as ep_autoconf_reset() isn't called at the time of
check_config()
- Fix compilation errors if CONFIG_OF is not defined
- Removed patch to add stubs for of_add_property()
Changes in V10:
- Fixed compilation errors in config where OF is not used (error due to
unknown symbol for of_add_property()). Add of_add_property() stub.
- Fixed compilation warning for incorrect argument being passed to dwc3_mdwidth
Changes in V9:
- Fixed incorrect patch in series. Removed changes in DTSI, as dwc3-qcom will
add the property by default from the kernel.
Changes in V8:
- Rebased to usb-testing
- Using devm_kzalloc for adding txfifo property in dwc3-qcom
- Removed DWC3 QCOM ACPI property for enabling the txfifo resize
Changes in V7:
- Added a new property tx-fifo-max-num for limiting how much fifo space the
resizing logic can allocate for endpoints with large burst values. This
can differ across platforms, and tie in closely with overall system latency.
- Added recommended checks for DWC32.
- Added changes to set the tx-fifo-resize property from dwc3-qcom by default
instead of modifying the current DTSI files.
- Added comments on all APIs/variables introduced.
- Updated the DWC3 YAML to include a better description of the tx-fifo-resize
property and added an entry for tx-fifo-max-num.
Changes in V6:
- Rebased patches to usb-testing.
- Renamed to PATCH series instead of RFC.
- Checking for fs_descriptors instead of ss_descriptors for determining the
endpoint count for a particular configuration.
- Re-ordered patch series to fix patch dependencies.
Changes in V5:
- Added check_config() logic, which is used to communicate the number of EPs
used in a particular configuration. Based on this, the DWC3 gadget driver
has the ability to know the maximum number of eps utilized in all configs.
This helps reduce unnecessary allocation to unused eps, and will catch fifo
allocation issues at bind() time.
- Fixed variable declaration to single line per variable, and reverse xmas.
- Created a helper for fifo clearing, which is used by ep0.c
Changes in V4:
- Removed struct dwc3* as an argument for dwc3_gadget_resize_tx_fifos()
- Removed WARN_ON(1) in case we run out of fifo space
Changes in V3:
- Removed "Reviewed-by" tags
- Renamed series back to RFC
- Modified logic to ensure that fifo_size is reset if we pass the minimum
threshold. Tested with binding multiple FDs requesting 6 FIFOs.
Changes in V2:
- Modified TXFIFO resizing logic to ensure that each EP is reserved a
FIFO.
- Removed dev_dbg() prints and fixed typos from patches
- Added some more description on the dt-bindings commit message
Currently, there is no functionality to allow for resizing the TXFIFOs, and
relying on the HW default setting for the TXFIFO depth. In most cases, the
HW default is probably sufficient, but for USB compositions that contain
multiple functions that require EP bursting, the default settings
might not be enough. Also to note, the current SW will assign an EP to a
function driver w/o checking to see if the TXFIFO size for that particular
EP is large enough. (this is a problem if there are multiple HW defined
values for the TXFIFO size)
It is mentioned in the SNPS databook that a minimum of TX FIFO depth = 3
is required for an EP that supports bursting. Otherwise, there may be
frequent occurences of bursts ending. For high bandwidth functions,
such as data tethering (protocols that support data aggregation), mass
storage, and media transfer protocol (over FFS), the bMaxBurst value can be
large, and a bigger TXFIFO depth may prove to be beneficial in terms of USB
throughput. (which can be associated to system access latency, etc...) It
allows for a more consistent burst of traffic, w/o any interruptions, as
data is readily available in the FIFO.
With testing done using the mass storage function driver, the results show
that with a larger TXFIFO depth, the bandwidth increased significantly.
Test Parameters:
- Platform: Qualcomm SM8150
- bMaxBurst = 6
- USB req size = 256kB
- Num of USB reqs = 16
- USB Speed = Super-Speed
- Function Driver: Mass Storage (w/ ramdisk)
- Test Application: CrystalDiskMark
Results:
TXFIFO Depth = 3 max packets
Test Case | Data Size | AVG tput (in MB/s)
-------------------------------------------
Sequential|1 GB x |
Read |9 loops | 193.60
| | 195.86
| | 184.77
| | 193.60
-------------------------------------------
TXFIFO Depth = 6 max packets
Test Case | Data Size | AVG tput (in MB/s)
-------------------------------------------
Sequential|1 GB x |
Read |9 loops | 287.35
| | 304.94
| | 289.64
| | 293.61
-------------------------------------------
Wesley Cheng (5):
usb: gadget: udc: core: Introduce check_config to verify USB
configuration
usb: gadget: configfs: Check USB configuration before adding
usb: dwc3: Resize TX FIFOs to meet EP bursting requirements
usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default
dt-bindings: usb: dwc3: Update dwc3 TX fifo properties
.../devicetree/bindings/usb/snps,dwc3.yaml | 15 +-
drivers/usb/dwc3/core.c | 9 +
drivers/usb/dwc3/core.h | 15 ++
drivers/usb/dwc3/dwc3-qcom.c | 21 ++
drivers/usb/dwc3/ep0.c | 2 +
drivers/usb/dwc3/gadget.c | 217 +++++++++++++++++++++
drivers/usb/gadget/configfs.c | 4 +
drivers/usb/gadget/udc/core.c | 25 +++
include/linux/usb/gadget.h | 4 +
9 files changed, 310 insertions(+), 2 deletions(-)
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
