Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.
Signed-off-by: Roja Rani Yarubandi <rojay@xxxxxxxxxxxxxx>
---
Changes in V3:
- Broken the huge V2 patch into 3 smaller patches.
1. QSPI DT nodes
2. QUP wrapper_0 DT nodes
3. QUP wrapper_1 DT nodes
Changes in V2:
- As per Doug's comments removed pinmux/pinconf subnodes.
- As per Doug's comments split of SPI, UART nodes has been done.
- Moved QSPI node before aps_smmu as per the order.
arch/arm64/boot/dts/qcom/sc7280-idp.dts | 97 ++-
arch/arm64/boot/dts/qcom/sc7280.dtsi | 750 +++++++++++++++++++++++-
2 files changed, 835 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index d0edffc15736..f57458dbe763 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -292,6 +292,16 @@ &uart5 {
status = "okay";
};
+&uart7 {
+ status = "okay";
+
+ /delete-property/interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
&qspi_cs0 {
@@ -307,16 +317,87 @@ &qspi_data01 {
bias-pull-up;
};
-&qup_uart5_default {
- tx {
- pins = "gpio46";
- drive-strength = <2>;
- bias-disable;
+&qup_uart5_tx {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart5_rx {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_uart7_cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+};
+
+&qup_uart7_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&tlmm {
+ qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+ pins = "gpio28";
+ function = "gpio";
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+ pins = "gpio29";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+ pins = "gpio30";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
};
- rx {
- pins = "gpio47";
- drive-strength = <2>;
+ qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+ pins = "gpio31";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
bias-pull-up;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 3047ab802cd2..b783f5622a66 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -431,6 +431,25 @@ ipcc: mailbox@408000 {
#mbox-cells = <2>;
};
+ qup_opp_table: qup-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-128000000 {
+ opp-hz = /bits/ 64 <128000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x009c0000 0 0x2000>;
@@ -440,16 +459,424 @@ qupv3_id_0: geniqup@9c0000 {
#address-cells = <2>;
#size-cells = <2>;
ranges;
+ iommus = <&apps_smmu 0x123 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>;
+ interconnect-names = "qup-core";
status = "disabled";
+ i2c0: i2c@980000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c0_data_clk>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi0: spi@980000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart0: serial@980000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c1: i2c@984000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_data_clk>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi1: spi@984000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>, <&qup_spi1_cs_gpio>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart1: serial@984000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c2: i2c@988000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_data_clk>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi2: spi@988000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>, <&qup_spi2_cs_gpio>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart2: serial@988000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c3: i2c@98c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_data_clk>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi3: spi@98c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>, <&qup_spi3_cs_gpio>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart3: serial@98c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c4: i2c@990000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_data_clk>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi4: spi@990000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>, <&qup_spi4_cs_gpio>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart4: serial@990000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c5: i2c@994000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00994000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_data_clk>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi5: spi@994000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00994000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>, <&qup_spi5_cs_gpio>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
uart5: serial@994000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x00994000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
pinctrl-names = "default";
- pinctrl-0 = <&qup_uart5_default>;
+ pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>;
interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c6: i2c@998000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_data_clk>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi6: spi@998000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>, <&qup_spi6_cs_gpio>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart6: serial@998000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c7: i2c@99c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c7_data_clk>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi7: spi@99c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>, <&qup_spi7_cs_gpio>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart7: serial@99c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
status = "disabled";
};
};
@@ -1247,9 +1674,324 @@ qspi_data12: qspi-data12 {
function = "qspi_data";
};
- qup_uart5_default: qup-uart5-default {
- pins = "gpio46", "gpio47";
- function = "qup13";
+ qup_i2c0_data_clk:qup-i2c0-data-clk {
+ pins = "gpio0", "gpio1";
+ function = "qup00";
+ };
+
+ qup_i2c1_data_clk:qup-i2c1-data-clk {
+ pins = "gpio4", "gpio5";
+ function = "qup01";
+ };
+
+ qup_i2c2_data_clk:qup-i2c2-data-clk {
+ pins = "gpio8", "gpio9";
+ function = "qup02";
+ };
+
+ qup_i2c3_data_clk:qup-i2c3-data-clk {
+ pins = "gpio12", "gpio13";
+ function = "qup03";
+ };
+
+ qup_i2c4_data_clk:qup-i2c4-data-clk {
+ pins = "gpio16", "gpio17";
+ function = "qup04";
+ };
+
+ qup_i2c5_data_clk:qup-i2c5-data-clk {
+ pins = "gpio20", "gpio21";
+ function = "qup05";
+ };
+
+ qup_i2c6_data_clk:qup-i2c6-data-clk {
+ pins = "gpio24", "gpio25";
+ function = "qup06";
+ };
+
+ qup_i2c7_data_clk:qup-i2c7-data-clk {
+ pins = "gpio28", "gpio29";
+ function = "qup07";
+ };
+
+ qup_spi0_data_clk: qup-spi0-data-clk {
+ pins = "gpio0", "gpio1", "gpio2";
+ function = "qup00";
+ };
+
+ qup_spi0_cs: qup-spi0-cs {
+ pins = "gpio3";
+ function = "qup00";
+ };
+
+ qup_spi0_cs_gpio: qup-spi0-cs_gpio {
+ pins = "gpio3";
+ function = "gpio";
+ };
+
+ qup_spi1_data_clk: qup-spi1-data-clk {
+ pins = "gpio4", "gpio5", "gpio6";
+ function = "qup01";
+ };
+
+ qup_spi1_cs: qup-spi1-cs {
+ pins = "gpio7";
+ function = "qup01";
+ };
+
+ qup_spi1_cs_gpio: qup-spi1-cs_gpio {
+ pins = "gpio7";
+ function = "gpio";
+ };
+
+ qup_spi2_data_clk: qup-spi2-data-clk {
+ pins = "gpio8", "gpio9", "gpio10";
+ function = "qup02";
+ };
+
+ qup_spi2_cs: qup-spi2-cs {
+ pins = "gpio11";
+ function = "qup02";
+ };
+
+ qup_spi2_cs_gpio: qup-spi2-cs_gpio {
+ pins = "gpio11";
+ function = "gpio";
+ };
+
+ qup_spi3_data_clk: qup-spi3-data-clk {
+ pins = "gpio12", "gpio13", "gpio14";
+ function = "qup03";
+ };
+
+ qup_spi3_cs: qup-spi3-cs {
+ pins = "gpio15";
+ function = "qup03";
+ };
+
+ qup_spi3_cs_gpio: qup-spi3-cs_gpio {
+ pins = "gpio15";
+ function = "gpio";
+ };
+
+ qup_spi4_data_clk: qup-spi4-data-clk {
+ pins = "gpio16", "gpio17", "gpio18";
+ function = "qup04";
+ };
+
+ qup_spi4_cs: qup-spi4-cs {
+ pins = "gpio19";
+ function = "qup04";
+ };
+
+ qup_spi4_cs_gpio: qup-spi4-cs_gpio {
+ pins = "gpio19";
+ function = "gpio";
+ };
+
+ qup_spi5_data_clk: qup-spi5-data-clk {
+ pins = "gpio20", "gpio21", "gpio22";
+ function = "qup05";
+ };
+
+ qup_spi5_cs: qup-spi5-cs {
+ pins = "gpio23";
+ function = "qup05";
+ };
+
+ qup_spi5_cs_gpio: qup-spi5-cs_gpio {
+ pins = "gpio23";
+ function = "gpio";
+ };
+
+ qup_spi6_data_clk: qup-spi6-data-clk {
+ pins = "gpio24", "gpio25", "gpio26";
+ function = "qup06";
+ };
+
+ qup_spi6_cs: qup-spi6-cs {
+ pins = "gpio27";
+ function = "qup06";
+ };
+
+ qup_spi6_cs_gpio: qup-spi6-cs_gpio {
+ pins = "gpio27";
+ function = "gpio";
+ };
+
+ qup_spi7_data_clk: qup-spi7-data-clk {
+ pins = "gpio28", "gpio29", "gpio30";
+ function = "qup07";
+ };
+
+ qup_spi7_cs: qup-spi7-cs {
+ pins = "gpio31";
+ function = "qup07";
+ };
+
+ qup_spi7_cs_gpio: qup-spi7-cs_gpio {
+ pins = "gpio31";
+ function = "gpio";
+ };
+
+ qup_uart0_cts: qup-uart0-cts {
+ pins = "gpio0";
+ function = "qup00";
+ };
+
+ qup_uart0_rts: qup-uart0-rts {
+ pins = "gpio1";
+ function = "qup00";
+ };
+
+ qup_uart0_tx: qup-uart0-tx {
+ pins = "gpio2";
+ function = "qup00";
+ };
+
+ qup_uart0_rx: qup-uart0-rx {
+ pins = "gpio3";
+ function = "qup00";
+ };
+
+ qup_uart1_cts: qup-uart1-cts {
+ pins = "gpio4";
+ function = "qup01";
+ };
+
+ qup_uart1_rts: qup-uart1-rts {
+ pins = "gpio5";
+ function = "qup01";
+ };
+
+ qup_uart1_tx: qup-uart1-tx {
+ pins = "gpio6";
+ function = "qup01";
+ };
+
+ qup_uart1_rx: qup-uart1-rx {
+ pins = "gpio7";
+ function = "qup01";
+ };
+
+ qup_uart2_cts: qup-uart2-cts {
+ pins = "gpio8";
+ function = "qup02";
+ };
+
+ qup_uart2_rts: qup-uart2-rts {
+ pins = "gpio9";
+ function = "qup02";
+ };
+
+ qup_uart2_tx: qup-uart2-tx {
+ pins = "gpio10";
+ function = "qup02";
+ };
+
+ qup_uart2_rx: qup-uart2-rx {
+ pins = "gpio11";
+ function = "qup02";
+ };
+
+ qup_uart3_cts: qup-uart3-cts {
+ pins = "gpio12";
+ function = "qup03";
+ };
+
+ qup_uart3_rts: qup-uart3-rts {
+ pins = "gpio13";
+ function = "qup03";
+ };
+
+ qup_uart3_tx: qup-uart3-tx {
+ pins = "gpio14";
+ function = "qup03";
+ };
+
+ qup_uart3_rx: qup-uart3-rx {
+ pins = "gpio15";
+ function = "qup03";
+ };
+
+ qup_uart4_cts: qup-uart4-cts {
+ pins = "gpio16";
+ function = "qup04";
+ };
+
+ qup_uart4_rts: qup-uart4-rts {
+ pins = "gpio17";
+ function = "qup04";
+ };
+
+ qup_uart4_tx: qup-uart4-tx {
+ pins = "gpio18";
+ function = "qup04";
+ };
+
+ qup_uart4_rx: qup-uart4-rx {
+ pins = "gpio19";
+ function = "qup04";
+ };
+
+ qup_uart5_cts: qup-uart5-cts {
+ pins = "gpio20";
+ function = "qup05";
+ };
+
+ qup_uart5_rts: qup-uart5-rts {
+ pins = "gpio21";
+ function = "qup05";
+ };
+
+ qup_uart5_tx: qup-uart5-tx {
+ pins = "gpio22";
+ function = "qup05";
+ };
+
+ qup_uart5_rx: qup-uart5-rx {
+ pins = "gpio23";
+ function = "qup05";
+ };
+
+ qup_uart6_cts: qup-uart6-cts {
+ pins = "gpio24";
+ function = "qup06";
+ };
+
+ qup_uart6_rts: qup-uart6-rts {
+ pins = "gpio25";
+ function = "qup06";
+ };
+
+ qup_uart6_tx: qup-uart6-tx {
+ pins = "gpio26";
+ function = "qup06";
+ };
+
+ qup_uart6_rx: qup-uart6-rx {
+ pins = "gpio27";
+ function = "qup06";
+ };
+
+ qup_uart7_cts: qup-uart7-cts {
+ pins = "gpio28";
+ function = "qup07";
+ };
+
+ qup_uart7_rts: qup-uart7-rts {
+ pins = "gpio29";
+ function = "qup07";
+ };
+
+ qup_uart7_tx: qup-uart7-tx {
+ pins = "gpio30";
+ function = "qup07";
+ };
+
+ qup_uart7_rx: qup-uart7-rx {
+ pins = "gpio31";
+ function = "qup07";
};
};
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
