Subject should be
"arm64: dts: qcom: sc7180: Add DisplayPort node"
Quoting Kuogee Hsieh (2021-06-02 14:08:38)
> Add DP device node on sc7180.
>
> Signed-off-by: Kuogee Hsieh <khsieh@xxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 9 ++++
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 77 ++++++++++++++++++++++++++++
> 2 files changed, 86 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> index 24d293e..53ef3961 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> @@ -786,6 +786,15 @@ hp_i2c: &i2c9 {
> status = "okay";
> };
>
> +&msm_dp {
Maybe the lable should just be 'dp' as msm_ prefix is redundant.
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&dp_hot_plug_det>;
> + data-lanes = <0 1>;
> + vdda-1p2-supply = <&vdda_usb_ss_dp_1p2>;
> + vdda-0p9-supply = <&vdda_usb_ss_dp_core>;
> +};
> +
> &pm6150_adc {
> charger-thermistor@4f {
> reg = <ADC5_AMUX_THM3_100K_PU>;
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 6228ba2..2e45098 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -3148,6 +3155,76 @@
>
> status = "disabled";
> };
> +
> + msm_dp: displayport-controller@ae90000 {
> + status = "disabled";
Can this come after compatible?
> + compatible = "qcom,sc7180-dp";
> +
> + reg = <0 0x0ae90000 0 0x1400>;
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <12 IRQ_TYPE_NONE>;
Should be
interrupts = <12>;
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
> + clock-names = "core_iface", "core_aux", "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + #clock-cells = <1>;
> + assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
> + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
> + assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>;
> + phys = <&dp_phy>;
> + phy-names = "dp";
> +
> + operating-points-v2 = <&dp_opp_table>;
> + power-domains = <&rpmhpd SC7180_CX>;
> +
> + #sound-dai-cells = <0>;
Move this next to phy? Or at least a newline here to split from ports.
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port@0 {
> + reg = <0>;
> + dp_in: endpoint {
> + remote-endpoint = <&dpu_intf0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dp_out: endpoint { };
> + };
> + };
> +
> + dp_opp_table: dp-opp-table {
Maybe node name should be opp-table?
dp_opp_table: opp-table {
};
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
