Re: [PATCH 2/2] arch: arm64: dts: msm8996: Add CPU opps

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu 27 May 14:44 CDT 2021, Konrad Dybcio wrote:

> From: Loic Poulain <loic.poulain@xxxxxxxxxx>
> 
> Add the operating points capabilities of the kryo CPUs, that can be
> used for frequency scaling. There are two differents operating point
> tables, one for the big cluster and one for the LITTLE cluster.
> 
> This frequency scaling support can then be used as a passive cooling
> device (cpufreq cooling device).
> 
> Only add nominal fmax for now, since there is no dynamic control of
> VDD APC (s11..) which is statically set at its nominal value.
> 
> Original patch link: https://patchwork.kernel.org/project/linux-arm-msm/patch/1595253740-29466-6-git-send-email-loic.poulain@xxxxxxxxxx/
> 
> Signed-off-by: Loic Poulain <loic.poulain@xxxxxxxxxx>
> [konrad: drop the thermals part, rebase and remove spaces within <>]
> Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>

As reported to Konrad on IRC, booting this causes a lockup before the
kernel reaches init, on one of my db820c boards. Booting with powersave
governor makes this board boot fine and I'm able to switch to
performance after that and at least according to cpufreq we're at full
speed on all 4 cores. But I haven't done any proper stress of the
system to narrow it down further...

PS. This was tested with next-20210527, your 3 patches, defconfig and
CONFIG_QCOM_CLK_APCC_MSM8996=y

Regards,
Bjorn

> ---
>  arch/arm64/boot/dts/qcom/msm8996.dtsi | 234 ++++++++++++++++++++++++++
>  1 file changed, 234 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> index 509d5bfec8ad..10e6fecc9e13 100644
> --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> @@ -8,6 +8,7 @@
>  #include <dt-bindings/clock/qcom,rpmcc.h>
>  #include <dt-bindings/power/qcom-rpmpd.h>
>  #include <dt-bindings/soc/qcom,apr.h>
> +#include <dt-bindings/thermal/thermal.h>
>  
>  / {
>  	interrupt-parent = <&intc>;
> @@ -44,6 +45,9 @@ CPU0: cpu@0 {
>  			enable-method = "psci";
>  			cpu-idle-states = <&CPU_SLEEP_0>;
>  			capacity-dmips-mhz = <1024>;
> +			clocks = <&kryocc 0>;
> +			operating-points-v2 = <&cluster0_opp>;
> +			#cooling-cells = <2>;
>  			next-level-cache = <&L2_0>;
>  			L2_0: l2-cache {
>  			      compatible = "cache";
> @@ -58,6 +62,9 @@ CPU1: cpu@1 {
>  			enable-method = "psci";
>  			cpu-idle-states = <&CPU_SLEEP_0>;
>  			capacity-dmips-mhz = <1024>;
> +			clocks = <&kryocc 0>;
> +			operating-points-v2 = <&cluster0_opp>;
> +			#cooling-cells = <2>;
>  			next-level-cache = <&L2_0>;
>  		};
>  
> @@ -68,6 +75,9 @@ CPU2: cpu@100 {
>  			enable-method = "psci";
>  			cpu-idle-states = <&CPU_SLEEP_0>;
>  			capacity-dmips-mhz = <1024>;
> +			clocks = <&kryocc 1>;
> +			operating-points-v2 = <&cluster1_opp>;
> +			#cooling-cells = <2>;
>  			next-level-cache = <&L2_1>;
>  			L2_1: l2-cache {
>  			      compatible = "cache";
> @@ -82,6 +92,9 @@ CPU3: cpu@101 {
>  			enable-method = "psci";
>  			cpu-idle-states = <&CPU_SLEEP_0>;
>  			capacity-dmips-mhz = <1024>;
> +			clocks = <&kryocc 1>;
> +			operating-points-v2 = <&cluster1_opp>;
> +			#cooling-cells = <2>;
>  			next-level-cache = <&L2_1>;
>  		};
>  
> @@ -121,6 +134,227 @@ CPU_SLEEP_0: cpu-sleep-0 {
>  		};
>  	};
>  
> +	cluster0_opp: opp_table0 {
> +		compatible = "operating-points-v2-kryo-cpu";
> +		nvmem-cells = <&speedbin_efuse>;
> +		opp-shared;
> +
> +		/* Nominal fmax for now */
> +		opp-307200000 {
> +			opp-hz = /bits/ 64 <307200000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-422400000 {
> +			opp-hz = /bits/ 64 <422400000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-480000000 {
> +			opp-hz = /bits/ 64 <480000000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-556800000 {
> +			opp-hz = /bits/ 64 <556800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-652800000 {
> +			opp-hz = /bits/ 64 <652800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-729600000 {
> +			opp-hz = /bits/ 64 <729600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-844800000 {
> +			opp-hz = /bits/ 64 <844800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-960000000 {
> +			opp-hz = /bits/ 64 <960000000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1036800000 {
> +			opp-hz = /bits/ 64 <1036800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1113600000 {
> +			opp-hz = /bits/ 64 <1113600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1190400000 {
> +			opp-hz = /bits/ 64 <1190400000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1228800000 {
> +			opp-hz = /bits/ 64 <1228800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1324800000 {
> +			opp-hz = /bits/ 64 <1324800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1401600000 {
> +			opp-hz = /bits/ 64 <1401600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1478400000 {
> +			opp-hz = /bits/ 64 <1478400000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1593600000 {
> +			opp-hz = /bits/ 64 <1593600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +	};
> +
> +	cluster1_opp: opp_table1 {
> +		compatible = "operating-points-v2-kryo-cpu";
> +		nvmem-cells = <&speedbin_efuse>;
> +		opp-shared;
> +
> +		/* Nominal fmax for now */
> +		opp-307200000 {
> +			opp-hz = /bits/ 64 <307200000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-403200000 {
> +			opp-hz = /bits/ 64 <403200000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-480000000 {
> +			opp-hz = /bits/ 64 <480000000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-556800000 {
> +			opp-hz = /bits/ 64 <556800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-652800000 {
> +			opp-hz = /bits/ 64 <652800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-729600000 {
> +			opp-hz = /bits/ 64 <729600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-806400000 {
> +			opp-hz = /bits/ 64 <806400000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-883200000 {
> +			opp-hz = /bits/ 64 <883200000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-940800000 {
> +			opp-hz = /bits/ 64 <940800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1036800000 {
> +			opp-hz = /bits/ 64 <1036800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1113600000 {
> +			opp-hz = /bits/ 64 <1113600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1190400000 {
> +			opp-hz = /bits/ 64 <1190400000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1248000000 {
> +			opp-hz = /bits/ 64 <1248000000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1324800000 {
> +			opp-hz = /bits/ 64 <1324800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1401600000 {
> +			opp-hz = /bits/ 64 <1401600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1478400000 {
> +			opp-hz = /bits/ 64 <1478400000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1555200000 {
> +			opp-hz = /bits/ 64 <1555200000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1632000000 {
> +			opp-hz = /bits/ 64 <1632000000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1708800000 {
> +			opp-hz = /bits/ 64 <1708800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1785600000 {
> +			opp-hz = /bits/ 64 <1785600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1824000000 {
> +			opp-hz = /bits/ 64 <1824000000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1920000000 {
> +			opp-hz = /bits/ 64 <1920000000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-1996800000 {
> +			opp-hz = /bits/ 64 <1996800000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-2073600000 {
> +			opp-hz = /bits/ 64 <2073600000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +		opp-2150400000 {
> +			opp-hz = /bits/ 64 <2150400000>;
> +			opp-supported-hw = <0x77>;
> +			clock-latency-ns = <200000>;
> +		};
> +	};
> +
>  	firmware {
>  		scm {
>  			compatible = "qcom,scm-msm8996";
> -- 
> 2.31.1
> 



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux