Hi Matthias,
On 2021-04-02 23:05, Matthias Kaehlcke wrote:
On Thu, Apr 01, 2021 at 02:43:12PM +0530, satya priya wrote:
subject: arm64: dts: qcom: pm7325: Add PMIC peripherals for pm7325
nit: maybe just 'arm64: dts: qcom: Add pm7325 support/.dtsi' or
similar?
Add temp-alarm and GPIO support for pm7325.
nit: it's more than that, you are adding the .dtsi for the PMIC itself.
Okay, will change the commit text.
Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/pm7325.dtsi | 53
++++++++++++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm7325.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm7325.dtsi
b/arch/arm64/boot/dts/qcom/pm7325.dtsi
new file mode 100644
index 0000000..1e0848a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm7325.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2021, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pm7325: pmic@1 {
+ compatible = "qcom,pm7325", "qcom,spmi-pmic";
I saw the patches that add the compatible strings for the GPIOs, but
can't find those that add the strings for the PMICs themselves. Could
you provide a link if they have been sent already?
They are not sent yet, qcom,spmi-pmic.txt file conversion to yaml [1] is
currently on hold as all the child node bindings needs to be converted
to yaml first. Once that is done we can add these strings.
[1] https://lore.kernel.org/patchwork/patch/1359552/
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm7325_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm7325_gpios: gpios@8800 {
+ compatible = "qcom,pm7325-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm7325_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
+
+&thermal_zones {
+ pm7325_thermal: pm7325-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+ thermal-sensors = <&pm7325_temp_alarm>;
+
+ trips {
+ pm7325_trip0: trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ pm7325_trip1: trip1 {
nit: the critical trip point is often named <name>-crit. One reason for
this could be that it allows to add other non-critical trip points (in
the .dtsi itself or the <board>.dts), without messing up the
enumeration scheme.
ok.
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+};
