Re: [PATCH V2 3/5] DCC: Added the sysfs entries for DCC(Data Capture and Compare) driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2021-03-30 01:39, Stephen Boyd wrote:
Quoting Souradeep Chowdhury (2021-03-25 01:02:34)
The DCC is a DMA engine designed to store register values either in
case of a system crash or in case of software triggers manually done
by the user.Using DCC hardware and the sysfs interface of the driver
the user can exploit various functionalities of DCC.The user can specify
the register addresses,the values of which is stored by DCC in it's
dedicated SRAM.The register addresses can be used either to read from,
write to,first read and store value and then write or to loop.All these
options can be exploited using the sysfs interface given to the user.
Following are the sysfs interfaces exposed in DCC driver which are
documented
1)trigger
2)config
3)config_write
4)config_reset
5)enable
6)rd_mod_wr
7)loop

Signed-off-by: Souradeep Chowdhury <schowdhu@xxxxxxxxxxxxxx>
---
Documentation/ABI/testing/sysfs-driver-dcc | 114 +++++++++++++++++++++++++++++

Please combine this with the driver patch.

Ack


 1 file changed, 114 insertions(+)
 create mode 100644 Documentation/ABI/testing/sysfs-driver-dcc

Perhaps this should be an ioctl interface instead of a sysfs interface?

The reasons for choosing sysfs over ioctl is as follows


i) As can be seen from the sysfs attribute descriptions, most of it does basic hardware manipulations like dcc_enable, dcc_disable, config reset etc. As a result sysfs is preferred over ioctl as we just need to enter a 0 or 1
signal in such cases.

ii) Existing similar debug hardwares are there for which drivers have been written using sysfs interface. One such example is the coresight-etm-trace driver. Following is the link for reference

https://www.kernel.org/doc/html/latest/trace/coresight/coresight-etm4x-reference.html



diff --git a/Documentation/ABI/testing/sysfs-driver-dcc b/Documentation/ABI/testing/sysfs-driver-dcc
new file mode 100644
index 0000000..05d24f0
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-dcc
@@ -0,0 +1,114 @@
+What:           /sys/bus/platform/devices/.../trigger
+Date:           March 2021
+Contact:        Souradeep Chowdhury <schowdhu@xxxxxxxxxxxxxx>
+Description:
+               This is the sysfs interface for manual software
+               triggers.The user can simply enter a 1 against
+               the sysfs file and enable a manual trigger.
+               Example:
+               echo  1 > /sys/bus/platform/devices/.../trigger
+
+What:           /sys/bus/platform/devices/.../enable
+Date:           March 2021
+Contact:        Souradeep Chowdhury <schowdhu@xxxxxxxxxxxxxx>
+Description:
+               This sysfs interface is used for enabling the
+               the dcc hardware.Without this being set to 1,

Space after period please.

Ack


+               the dcc hardware ceases to function.
+               Example:
+               echo  0 > /sys/bus/platform/devices/.../enable
+               (disable interface)
+               echo  1 > /sys/bus/platform/devices/.../enable
+               (enable interface)
+
+What:           /sys/bus/platform/devices/.../config
+Date:           March 2021
+Contact:        Souradeep Chowdhury <schowdhu@xxxxxxxxxxxxxx>
+Description:
+               This is the most commonly used sysfs interface
+               file and this basically stores the addresses of
+               the registers which needs to be read in case of
+               a hardware crash or manual software triggers.
+               Example:
+ echo 0x80000010 10 > /sys/bus/platform/devices/../config
+               This specifies that 10 words starting from address
+ 0x80000010 is to be read.In case there are no words to be
+               specified we can simply enter the address.
+
+What:           /sys/bus/platform/devices/.../config_write
+Date:           March 2021
+Contact:        Souradeep Chowdhury <schowdhu@xxxxxxxxxxxxxx>
+Description:
+               This file allows user to write a value to the register
+ address given as argument.The values are entered in the
+               form of <register_address> <value>.The reason for this
+               feature of dcc is that for accessing certain registers
+ it is necessary to set some bits of soe other register.

s/soe/some/?

Ack


+               That is achievable by giving DCC this privelege.

s/privelege/privilege/

Ack


+               Example:
+ echo 0x80000000 0xFF > /sys/bus/platform/devices/.../config_write
+
+What:           /sys/bus/platform/devices/.../config_reset
+Date:           March 2021
+Contact:        Souradeep Chowdhury <schowdhu@xxxxxxxxxxxxxx>
+Description:
+               This file is used to reset the configuration of
+               a dcc driver to the default configuration.
+               Example:
+               echo  1 > /sys/bus/platform/devices/.../config_reset
+



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux