From: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
Previous pinctrl configuration was wrong. Fix it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sdm630.dtsi | 221 ++++++++++++++++++---------
1 file changed, 145 insertions(+), 76 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi
index 551b70a8f22a..410a97ea2bb3 100644
--- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
@@ -626,14 +626,18 @@ tcsr_mutex_regs: syscon@1f40000 {
reg = <0x01f40000 0x20000>;
};
- tlmm: pinctrl@3000000 {
+ tlmm: pinctrl@3100000 {
compatible = "qcom,sdm630-pinctrl";
- reg = <0x03000000 0xc00000>;
+ reg = <0x03100000 0x400000>,
+ <0x03500000 0x400000>,
+ <0x03900000 0x400000>;
+ reg-names = "south", "center", "north";
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
- #gpio-cells = <0x2>;
+ gpio-ranges = <&tlmm 0 0 114>;
+ #gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <0x2>;
+ #interrupt-cells = <2>;
blsp1_uart1_default: blsp1-uart1-default {
pins = "gpio0", "gpio1", "gpio2", "gpio3";
@@ -653,40 +657,51 @@ blsp1_uart2_default: blsp1-uart2-default {
bias-disable;
};
- blsp2_uart1_tx_active: blsp2-uart1-tx-active {
- pins = "gpio16";
- drive-strength = <2>;
- bias-disable;
- };
-
- blsp2_uart1_tx_sleep: blsp2-uart1-tx-sleep {
- pins = "gpio16";
- drive-strength = <2>;
- bias-pull-up;
- };
-
- blsp2_uart1_rxcts_active: blsp2-uart1-rxcts-active {
- pins = "gpio17", "gpio18";
- drive-strength = <2>;
- bias-disable;
- };
-
- blsp2_uart1_rxcts_sleep: blsp2-uart1-rxcts-sleep {
- pins = "gpio17", "gpio18";
- drive-strength = <2>;
- bias-no-pull;
- };
-
- blsp2_uart1_rfr_active: blsp2-uart1-rfr-active {
- pins = "gpio19";
- drive-strength = <2>;
- bias-disable;
+ blsp2_uart1_default: blsp2-uart1-active {
+ pinmux {
+ pins = "gpio16", "gpio17",
+ "gpio18", "gpio19";
+ function = "blsp_uart5";
+ };
+ pinconf-tx-rts {
+ pins = "gpio16", "gpio19";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ pinconf-rx {
+ /*
+ * Avoid garbage data while BT module
+ * is powered off or not driving signal
+ */
+ pins = "gpio17";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ pinconf-cts {
+ /* Match the pull of the BT module */
+ pins = "gpio18";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
};
- blsp2_uart1_rfr_sleep: blsp2-uart1-rfr-sleep {
- pins = "gpio19";
- drive-strength = <2>;
- bias-no-pull;
+ blsp2_uart1_sleep: blsp2-uart1-sleep {
+ pinmux {
+ pins = "gpio16", "gpio17",
+ "gpio18", "gpio19";
+ function = "gpio";
+ };
+ pinconf-tx {
+ pins = "gpio16";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ pinconf-rx-cts-rts {
+ pins = "gpio17", "gpio18",
+ "gpio19";
+ drive-strength = <2>;
+ bias-no-pull;
+ };
};
i2c1_default: i2c1-default {
@@ -785,50 +800,106 @@ i2c8_sleep: i2c8-sleep {
bias-pull-up;
};
- sdc1_clk_on: sdc1-clk-on {
- pins = "sdc1_clk";
- bias-disable;
- drive-strength = <16>;
- };
+ sdc1_state_on: sdc1-on {
+ pinconf-clk {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
- sdc1_clk_off: sdc1-clk-off {
- pins = "sdc1_clk";
- bias-disable;
- drive-strength = <2>;
- };
+ pinconf-cmd {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
- sdc1_cmd_on: sdc1-cmd-on {
- pins = "sdc1_cmd";
- bias-pull-up;
- drive-strength = <10>;
- };
+ pinconf-data {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
- sdc1_cmd_off: sdc1-cmd-off {
- pins = "sdc1_cmd";
- bias-pull-up;
- drive-strength = <2>;
+ pinconf-rclk {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
};
- sdc1_data_on: sdc1-data-on {
- pins = "sdc1_data";
- bias-pull-up;
- drive-strength = <8>;
- };
+ sdc1_state_off: sdc1-off {
+ pinconf-clk {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
- sdc1_data_off: sdc1-data-off {
- pins = "sdc1_data";
- bias-pull-up;
- drive-strength = <2>;
+ pinconf-cmd {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ pinconf-data {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ pinconf-rclk {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
};
- sdc1_rclk_on: sdc1-rclk-on {
- pins = "sdc1_rclk";
- bias-pull-down;
+ sdc2_state_on: sdc2-on {
+ pinconf-clk {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ pinconf-cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ pinconf-data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ pinconf-sd-cd {
+ pins = "gpio54";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
};
- sdc1_rclk_off: sdc1-rclk-off {
- pins = "sdc1_rclk";
- bias-pull-down;
+ sdc2_state_off: sdc2-off {
+ pinconf-clk {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ pinconf-cmd {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ pinconf-data {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ pinconf-sd-cd {
+ pins = "gpio54";
+ bias-disable;
+ drive-strength = <2>;
+ };
};
};
@@ -986,8 +1057,8 @@ sdhc_1: sdhci@c0c4000 {
clock-names = "core", "iface", "xo", "ice";
pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>;
- pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>;
+ pinctrl-0 = <&sdc1_state_on>;
+ pinctrl-1 = <&sdc1_state_off>;
bus-width = <8>;
non-removable;
@@ -1354,10 +1425,8 @@ blsp2_uart1: serial@c1af000 {
dmas = <&blsp2_dma 0>, <&blsp2_dma 1>;
dma-names = "tx", "rx";
pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp2_uart1_tx_active &blsp2_uart1_rxcts_active
- &blsp2_uart1_rfr_active>;
- pinctrl-1 = <&blsp2_uart1_tx_sleep &blsp2_uart1_rxcts_sleep
- &blsp2_uart1_rfr_sleep>;
+ pinctrl-0 = <&blsp2_uart1_default>;
+ pinctrl-1 = <&blsp2_uart1_sleep>;
status = "disabled";
};
--
2.30.1
