Add support for EM1XXGR-L modems, this modem series is based on SDX24
qcom chip. The modem is mainly based on MBIM protocol for both the
data and control path. The drivers for these channels (mhi-net-mbim and
mhi_uci) are not yet part of the kernel but will be integrated by
different series.
Signed-off-by: Loic Poulain <loic.poulain@xxxxxxxxxx>
---
v2: Specify 256 elements for the hardware event rings
v3: increase hw event elements to 1024 (aligned with downstream)
drivers/bus/mhi/pci_generic.c | 73 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index c58bf96..42b3952 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -114,6 +114,36 @@ struct mhi_pci_dev_info {
.doorbell_mode_switch = true, \
}
+#define MHI_CHANNEL_CONFIG_UL_SBL(ch_num, ch_name, el_count, ev_ring) \
+ { \
+ .num = ch_num, \
+ .name = ch_name, \
+ .num_elements = el_count, \
+ .event_ring = ev_ring, \
+ .dir = DMA_TO_DEVICE, \
+ .ee_mask = BIT(MHI_EE_SBL), \
+ .pollcfg = 0, \
+ .doorbell = MHI_DB_BRST_DISABLE, \
+ .lpm_notify = false, \
+ .offload_channel = false, \
+ .doorbell_mode_switch = false, \
+ } \
+
+#define MHI_CHANNEL_CONFIG_DL_SBL(ch_num, ch_name, el_count, ev_ring) \
+ { \
+ .num = ch_num, \
+ .name = ch_name, \
+ .num_elements = el_count, \
+ .event_ring = ev_ring, \
+ .dir = DMA_FROM_DEVICE, \
+ .ee_mask = BIT(MHI_EE_SBL), \
+ .pollcfg = 0, \
+ .doorbell = MHI_DB_BRST_DISABLE, \
+ .lpm_notify = false, \
+ .offload_channel = false, \
+ .doorbell_mode_switch = false, \
+ }
+
#define MHI_EVENT_CONFIG_DATA(ev_ring, el_count) \
{ \
.num_elements = el_count, \
@@ -182,9 +212,52 @@ static const struct mhi_pci_dev_info mhi_qcom_sdx55_info = {
.dma_data_width = 32
};
+static const struct mhi_channel_config mhi_quectel_em1xx_channels[] = {
+ MHI_CHANNEL_CONFIG_UL(0, "NMEA", 32, 0),
+ MHI_CHANNEL_CONFIG_DL(1, "NMEA", 32, 0),
+ MHI_CHANNEL_CONFIG_UL_SBL(2, "SAHARA", 32, 0),
+ MHI_CHANNEL_CONFIG_DL_SBL(3, "SAHARA", 32, 0),
+ MHI_CHANNEL_CONFIG_UL(4, "DIAG", 32, 1),
+ MHI_CHANNEL_CONFIG_DL(5, "DIAG", 32, 1),
+ MHI_CHANNEL_CONFIG_UL(12, "MBIM", 32, 0),
+ MHI_CHANNEL_CONFIG_DL(13, "MBIM", 32, 0),
+ MHI_CHANNEL_CONFIG_UL(32, "DUN", 32, 0),
+ MHI_CHANNEL_CONFIG_DL(33, "DUN", 32, 0),
+ MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0_MBIM", 128, 2),
+ MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0_MBIM", 128, 3),
+};
+
+static struct mhi_event_config mhi_quectel_em1xx_events[] = {
+ MHI_EVENT_CONFIG_CTRL(0, 128),
+ MHI_EVENT_CONFIG_DATA(1, 128),
+ MHI_EVENT_CONFIG_HW_DATA(2, 1024, 100),
+ MHI_EVENT_CONFIG_HW_DATA(3, 1024, 101)
+};
+
+static struct mhi_controller_config modem_quectel_em1xx_config = {
+ .max_channels = 128,
+ .timeout_ms = 8000,
+ .num_channels = ARRAY_SIZE(mhi_quectel_em1xx_channels),
+ .ch_cfg = mhi_quectel_em1xx_channels,
+ .num_events = ARRAY_SIZE(mhi_quectel_em1xx_events),
+ .event_cfg = mhi_quectel_em1xx_events,
+};
+
+static const struct mhi_pci_dev_info mhi_quectel_em1xx_info = {
+ .name = "quectel-em1xx",
+ .edl = "quectel/prog_firehose_sdx24.mbn",
+ .config = &modem_quectel_em1xx_config,
+ .bar_num = MHI_PCI_DEFAULT_BAR_NUM,
+ .dma_data_width = 32
+};
+
static const struct pci_device_id mhi_pci_id_table[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_QCOM, 0x0306),
.driver_data = (kernel_ulong_t) &mhi_qcom_sdx55_info },
+ { PCI_DEVICE(0x1eac, 0x1001), /* EM120R-GL (sdx24) */
+ .driver_data = (kernel_ulong_t) &mhi_quectel_em1xx_info },
+ { PCI_DEVICE(0x1eac, 0x1002), /* EM160R-GL (sdx24) */
+ .driver_data = (kernel_ulong_t) &mhi_quectel_em1xx_info },
{ }
};
MODULE_DEVICE_TABLE(pci, mhi_pci_id_table);
--
2.7.4
