On Thu 21 Jan 22:01 CST 2021, Wesley Cheng wrote:
> Some devices have USB compositions which may require multiple endpoints
> that support EP bursting. HW defined TX FIFO sizes may not always be
> sufficient for these compositions. By utilizing flexible TX FIFO
> allocation, this allows for endpoints to request the required FIFO depth to
> achieve higher bandwidth. With some higher bMaxBurst configurations, using
> a larger TX FIFO size results in better TX throughput.
>
> By introducing the check_config() callback, the resizing logic can fetch
> the maximum number of endpoints used in the USB composition (can contain
> multiple configurations), which helps ensure that the resizing logic can
> fulfill the configuration(s), or return an error to the gadget layer
> otherwise during bind time.
>
> Signed-off-by: Wesley Cheng <wcheng@xxxxxxxxxxxxxx>
> ---
> drivers/usb/dwc3/core.c | 2 +
> drivers/usb/dwc3/core.h | 8 ++
> drivers/usb/dwc3/ep0.c | 2 +
> drivers/usb/dwc3/gadget.c | 194 ++++++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 206 insertions(+)
>
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 6969196..e7fa6af 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -1284,6 +1284,8 @@ static void dwc3_get_properties(struct dwc3 *dwc)
> &tx_thr_num_pkt_prd);
> device_property_read_u8(dev, "snps,tx-max-burst-prd",
> &tx_max_burst_prd);
> + dwc->needs_fifo_resize = device_property_read_bool(dev,
> + "tx-fifo-resize");
Under what circumstances should we specify this? And in particular are
there scenarios (in the Qualcomm platforms) where this must not be set?
In particular, the composition can be changed in runtime, so should we
set this for all Qualcomm platforms?
And if that's the case, can we not just set it from the qcom driver?
Regards,
Bjorn
>
> dwc->disable_scramble_quirk = device_property_read_bool(dev,
> "snps,disable_scramble_quirk");
> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> index eec1cf4..983b2fd4 100644
> --- a/drivers/usb/dwc3/core.h
> +++ b/drivers/usb/dwc3/core.h
> @@ -1223,6 +1223,7 @@ struct dwc3 {
> unsigned is_utmi_l1_suspend:1;
> unsigned is_fpga:1;
> unsigned pending_events:1;
> + unsigned needs_fifo_resize:1;
> unsigned pullups_connected:1;
> unsigned setup_packet_pending:1;
> unsigned three_stage_setup:1;
> @@ -1257,6 +1258,10 @@ struct dwc3 {
> unsigned dis_split_quirk:1;
>
> u16 imod_interval;
> +
> + int max_cfg_eps;
> + int last_fifo_depth;
> + int num_ep_resized;
> };
>
> #define INCRX_BURST_MODE 0
> @@ -1471,6 +1476,7 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
> struct dwc3_gadget_ep_cmd_params *params);
> int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
> u32 param);
> +void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
> #else
> static inline int dwc3_gadget_init(struct dwc3 *dwc)
> { return 0; }
> @@ -1490,6 +1496,8 @@ static inline int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
> static inline int dwc3_send_gadget_generic_command(struct dwc3 *dwc,
> int cmd, u32 param)
> { return 0; }
> +static inline void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
> +{ }
> #endif
>
> #if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
> index 8b668ef..4f216bd 100644
> --- a/drivers/usb/dwc3/ep0.c
> +++ b/drivers/usb/dwc3/ep0.c
> @@ -616,6 +616,8 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
> return -EINVAL;
>
> case USB_STATE_ADDRESS:
> + dwc3_gadget_clear_tx_fifos(dwc);
> +
> ret = dwc3_ep0_delegate_req(dwc, ctrl);
> /* if the cfg matches and the cfg is non zero */
> if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {
> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
> index 86f257f..26f9d64 100644
> --- a/drivers/usb/dwc3/gadget.c
> +++ b/drivers/usb/dwc3/gadget.c
> @@ -615,6 +615,161 @@ static int dwc3_gadget_set_ep_config(struct dwc3_ep *dep, unsigned int action)
> static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
> bool interrupt);
>
> +static int dwc3_gadget_calc_tx_fifo_size(struct dwc3 *dwc, int mult)
> +{
> + int max_packet = 1024;
> + int fifo_size;
> + int mdwidth;
> +
> + mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);
> + /* MDWIDTH is represented in bits, we need it in bytes */
> + mdwidth >>= 3;
> +
> + fifo_size = mult * ((max_packet + mdwidth) / mdwidth) + 1;
> + return fifo_size;
> +}
> +
> +void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
> +{
> + struct dwc3_ep *dep;
> + int fifo_depth;
> + int size;
> + int num;
> +
> + if (!dwc->needs_fifo_resize)
> + return;
> +
> + /* Read ep0IN related TXFIFO size */
> + dep = dwc->eps[1];
> + size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
> + if (DWC3_IP_IS(DWC31))
> + fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);
> + else
> + fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);
> +
> + dwc->last_fifo_depth = fifo_depth;
> + /* Clear existing TXFIFO for all IN eps except ep0 */
> + for (num = 3; num < min_t(int, dwc->num_eps, DWC3_ENDPOINTS_NUM);
> + num += 2) {
> + dep = dwc->eps[num];
> + /* Don't change TXFRAMNUM on usb31 version */
> + size = DWC3_IP_IS(DWC31) ?
> + dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1)) &
> + DWC31_GTXFIFOSIZ_TXFRAMNUM : 0;
> +
> + dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1), size);
> + }
> + dwc->num_ep_resized = 0;
> +}
> +
> +/*
> + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
> + * @dwc: pointer to our context structure
> + *
> + * This function will a best effort FIFO allocation in order
> + * to improve FIFO usage and throughput, while still allowing
> + * us to enable as many endpoints as possible.
> + *
> + * Keep in mind that this operation will be highly dependent
> + * on the configured size for RAM1 - which contains TxFifo -,
> + * the amount of endpoints enabled on coreConsultant tool, and
> + * the width of the Master Bus.
> + *
> + * In general, FIFO depths are represented with the following equation:
> + *
> + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
> + *
> + * Conversions can be done to the equation to derive the number of packets that
> + * will fit to a particular FIFO size value.
> + */
> +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
> +{
> + struct dwc3 *dwc = dep->dwc;
> + int fifo_0_start;
> + int ram1_depth;
> + int fifo_size;
> + int min_depth;
> + int num_in_ep;
> + int remaining;
> + int mult = 1;
> + int fifo;
> + int tmp;
> +
> + if (!dwc->needs_fifo_resize)
> + return 0;
> +
> + /* resize IN endpoints except ep0 */
> + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
> + return 0;
> +
> + ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
> +
> + if ((dep->endpoint.maxburst > 1 &&
> + usb_endpoint_xfer_bulk(dep->endpoint.desc)) ||
> + usb_endpoint_xfer_isoc(dep->endpoint.desc))
> + mult = 3;
> +
> + if (dep->endpoint.maxburst > 6 &&
> + usb_endpoint_xfer_bulk(dep->endpoint.desc) && DWC3_IP_IS(DWC31))
> + mult = 6;
> +
> + /* FIFO size for a single buffer */
> + fifo = dwc3_gadget_calc_tx_fifo_size(dwc, 1);
> +
> + /* Calculate the number of remaining EPs w/o any FIFO */
> + num_in_ep = dwc->max_cfg_eps;
> + num_in_ep -= dwc->num_ep_resized;
> +
> + /* Reserve at least one FIFO for the number of IN EPs */
> + min_depth = num_in_ep * (fifo + 1);
> + remaining = ram1_depth - min_depth - dwc->last_fifo_depth;
> +
> + /*
> + * We've already reserved 1 FIFO per EP, so check what we can fit in
> + * addition to it. If there is not enough remaining space, allocate
> + * all the remaining space to the EP.
> + */
> + fifo_size = (mult - 1) * fifo;
> + if (remaining < fifo_size) {
> + if (remaining > 0)
> + fifo_size = remaining;
> + else
> + fifo_size = 0;
> + }
> +
> + fifo_size += fifo;
> + /* Last increment according to the TX FIFO size equation */
> + fifo_size++;
> +
> + /* Check if TXFIFOs start at non-zero addr */
> + tmp = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
> + fifo_0_start = DWC3_GTXFIFOSIZ_TXFSTADDR(tmp);
> +
> + fifo_size |= (fifo_0_start + (dwc->last_fifo_depth << 16));
> + if (DWC3_IP_IS(DWC31))
> + dwc->last_fifo_depth += DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
> + else
> + dwc->last_fifo_depth += DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
> +
> + /* Check fifo size allocation doesn't exceed available RAM size. */
> + if (dwc->last_fifo_depth >= ram1_depth) {
> + dev_err(dwc->dev, "Fifosize(%d) > RAM size(%d) %s depth:%d\n",
> + dwc->last_fifo_depth, ram1_depth,
> + dep->endpoint.name, fifo_size);
> + if (DWC3_IP_IS(DWC31))
> + fifo_size = DWC31_GTXFIFOSIZ_TXFDEP(fifo_size);
> + else
> + fifo_size = DWC3_GTXFIFOSIZ_TXFDEP(fifo_size);
> + dwc->last_fifo_depth -= fifo_size;
> + return -ENOMEM;
> + }
> +
> + dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(dep->number >> 1), fifo_size);
> + dwc->num_ep_resized++;
> +
> + return 0;
> +}
> +
> /**
> * __dwc3_gadget_ep_enable - initializes a hw endpoint
> * @dep: endpoint to be initialized
> @@ -632,6 +787,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
> int ret;
>
> if (!(dep->flags & DWC3_EP_ENABLED)) {
> + ret = dwc3_gadget_resize_tx_fifos(dep);
> + if (ret)
> + return ret;
> +
> ret = dwc3_gadget_start_config(dep);
> if (ret)
> return ret;
> @@ -2418,6 +2577,7 @@ static int dwc3_gadget_stop(struct usb_gadget *g)
>
> spin_lock_irqsave(&dwc->lock, flags);
> dwc->gadget_driver = NULL;
> + dwc->max_cfg_eps = 0;
> spin_unlock_irqrestore(&dwc->lock, flags);
>
> free_irq(dwc->irq_gadget, dwc->ev_buf);
> @@ -2485,6 +2645,39 @@ static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA)
> return 0;
> }
>
> +static int dwc3_gadget_check_config(struct usb_gadget *g, unsigned long ep_map)
> +{
> + struct dwc3 *dwc = gadget_to_dwc(g);
> + unsigned long in_ep_map;
> + int fifo_size = 0;
> + int ram1_depth;
> + int ep_num;
> +
> + if (!dwc->needs_fifo_resize)
> + return 0;
> +
> + /* Only interested in the IN endpoints */
> + in_ep_map = ep_map >> 16;
> + ep_num = hweight_long(in_ep_map);
> +
> + if (ep_num <= dwc->max_cfg_eps)
> + return 0;
> +
> + /* Update the max number of eps in the composition */
> + dwc->max_cfg_eps = ep_num;
> +
> + fifo_size = dwc3_gadget_calc_tx_fifo_size(dwc, dwc->max_cfg_eps);
> + /* Based on the equation, increment by one for every ep */
> + fifo_size += dwc->max_cfg_eps;
> +
> + /* Check if we can fit a single fifo per endpoint */
> + ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
> + if (fifo_size > ram1_depth)
> + return -ENOMEM;
> +
> + return 0;
> +}
> +
> static const struct usb_gadget_ops dwc3_gadget_ops = {
> .get_frame = dwc3_gadget_get_frame,
> .wakeup = dwc3_gadget_wakeup,
> @@ -2495,6 +2688,7 @@ static const struct usb_gadget_ops dwc3_gadget_ops = {
> .udc_set_speed = dwc3_gadget_set_speed,
> .get_config_params = dwc3_gadget_config_params,
> .vbus_draw = dwc3_gadget_vbus_draw,
> + .check_config = dwc3_gadget_check_config,
> };
>
> /* -------------------------------------------------------------------------- */
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
