Re: [PATCH 2/4] clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Il 05/01/21 16:46, Vinod Koul ha scritto:
From: Vivek Aknurwar <viveka@xxxxxxxxxxxxxx>

Lucid 5LPE is a slightly different Lucid PLL with different offsets and
porgramming sequence so add support for these

Signed-off-by: Vivek Aknurwar <viveka@xxxxxxxxxxxxxx>
Signed-off-by: Jeevan Shriram <jshriram@xxxxxxxxxxxxxx>
[vkoul: rebase and tidy up for upstream]
Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
---
  drivers/clk/qcom/clk-alpha-pll.c | 217 +++++++++++++++++++++++++++++++
  drivers/clk/qcom/clk-alpha-pll.h |   4 +
  2 files changed, 221 insertions(+)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index f7721088494c..843c43649a5a 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -156,6 +156,12 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
  /* LUCID PLL specific settings and offsets */
  #define LUCID_PCAL_DONE		BIT(27)
+/* LUCID 5LPE PLL specific settings and offsets */
+#define LUCID_5LPE_PCAL_DONE		BIT(11)
+#define LUCID_5LPE_ALPHA_PLL_ACK_LATCH	BIT(13)
+#define LUCID_5LPE_PLL_LATCH_INPUT	BIT(14)
+#define LUCID_5LPE_ENABLE_VOTE_RUN	BIT(21)
+
  #define pll_alpha_width(p)					\
  		((PLL_ALPHA_VAL_U(p) - PLL_ALPHA_VAL(p) == 4) ?	\
  				 ALPHA_REG_BITWIDTH : ALPHA_REG_16BIT_WIDTH)
@@ -1600,3 +1606,214 @@ const struct clk_ops clk_alpha_pll_agera_ops = {
  	.set_rate = clk_alpha_pll_agera_set_rate,
  };
  EXPORT_SYMBOL_GPL(clk_alpha_pll_agera_ops);
+
+static int alpha_pll_lucid_5lpe_enable(struct clk_hw *hw)
+{
+	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+	u32 val;
+	int ret;
+
+	ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
+	if (ret)
+		return ret;
+
+	/* If in FSM mode, just vote for it */
+	if (val & LUCID_5LPE_ENABLE_VOTE_RUN) {
+		ret = clk_enable_regmap(hw);
+		if (ret)
+			return ret;
+		return wait_for_pll_enable_lock(pll);
+	}
+
+	/* Check if PLL is already enabled, return if enabled */
+	ret = trion_pll_is_enabled(pll, pll->clkr.regmap);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
+	if (ret)
+		return ret;
+
+	regmap_write(pll->clkr.regmap, PLL_OPMODE(pll), PLL_RUN);
+
+	ret = wait_for_pll_enable_lock(pll);
+	if (ret)
+		return ret;
+
+	/* Enable the PLL outputs */
+	ret = regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, PLL_OUT_MASK);
+	if (ret)
+		return ret;
+
+	/* Enable the global PLL outputs */
+	return regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_OUTCTRL, PLL_OUTCTRL);
+}
+
+static void alpha_pll_lucid_5lpe_disable(struct clk_hw *hw)
+{
+	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+	u32 val;
+	int ret;
+
+	ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
+	if (ret)
+		return;
+
+	/* If in FSM mode, just unvote it */
+	if (val & LUCID_5LPE_ENABLE_VOTE_RUN) {
+		clk_disable_regmap(hw);
+		return;
+	}
+
+	/* Disable the global PLL output */
+	ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_OUTCTRL, 0);
+	if (ret)
+		return;
+
+	/* Disable the PLL outputs */
+	ret = regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, 0);
+	if (ret)
+		return;
+
+	/* Place the PLL mode in STANDBY */
+	regmap_write(pll->clkr.regmap, PLL_OPMODE(pll), PLL_STANDBY);
+}
+
+/*
+ * The Lucid 5LPE PLL requires a power-on self-calibration which happens
+ * when the PLL comes out of reset. Calibrate in case it is not completed.
+ */
+static int alpha_pll_lucid_5lpe_prepare(struct clk_hw *hw)
+{
+	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+	struct clk_hw *p;
+	u32 val;
+	int ret;
+
+	/* Return early if calibration is not needed. */
+	regmap_read(pll->clkr.regmap, PLL_MODE(pll), &val);
+	if (val & LUCID_5LPE_PCAL_DONE)
+		return 0;
+
+	p = clk_hw_get_parent(hw);
+	if (!p)
+		return -EINVAL;
+
+	ret = alpha_pll_lucid_5lpe_enable(hw);
+	if (ret)
+		return ret;
+
+	alpha_pll_lucid_5lpe_disable(hw);
+
+	return 0;
+}
+
+static int alpha_pll_lucid_5lpe_set_rate(struct clk_hw *hw, unsigned long rate,
+					 unsigned long prate)
+{
+	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+	unsigned long rrate;
+	u32 val, l;
+	u64 a;
+	int ret;
+
+	rrate = alpha_pll_round_rate(rate, prate, &l, &a, ALPHA_REG_16BIT_WIDTH);
+
+	/*
+	 * Due to a limited number of bits for fractional rate programming, the
+	 * rounded up rate could be marginally higher than the requested rate.
+	 */
+	ret = alpha_pll_check_rate_margin(hw, rrate, rate);
+	if (ret)
+		return ret;
+
+	regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
+	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
+
+	/* Latch the PLL input */
+	ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll),
+				 LUCID_5LPE_PLL_LATCH_INPUT, LUCID_5LPE_PLL_LATCH_INPUT);
+	if (ret)
+		return ret;
+
+	/* Wait for 2 reference cycles before checking the ACK bit. */
+	udelay(1);
+	regmap_read(pll->clkr.regmap, PLL_MODE(pll), &val);
+	if (!(val & LUCID_5LPE_ALPHA_PLL_ACK_LATCH)) {
+		pr_err("Lucid 5LPE PLL latch failed. Output may be unstable!\n");
+		return -EINVAL;
+	}
+
+	/* Return the latch input to 0 */
+	ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), LUCID_5LPE_PLL_LATCH_INPUT, 0);
+	if (ret)
+		return ret;
+
+	if (clk_hw_is_enabled(hw)) {
+		ret = wait_for_pll_enable_lock(pll);
+		if (ret)
+			return ret;
+	}
+
+	/* Wait for PLL output to stabilize */
+	udelay(100);
+	return 0;
+}
+

This one looks exactly like alpha_pll_trion_set_rate() but:
1. You are forcing ALPHA_REG_16BIT_WIDTH for the alpha_pll_round_rate
   call: this is bad, you should actually use pll_alpha_width(pll) here,
   unless you have a very good reason that I didn't understand...
2. The only change between these two functions (trion and
   lucid_5lpe_set_rate) is that PLL_UPDATE becomes
   LUCID_5LPE_PLL_LATCH_INPUT, and that you check for
   LUCID_5LPE_ALPHA_PLL_ACK_LATCH instead of ALPHA_PLL_ACK_LATCH: this
   looks like being 95% code duplication.

The best options here, in my opinion, would be to commonize the function
alpha_pll_trion_set_rate: that will avoid this huge duplication.

+static int clk_lucid_5lpe_pll_postdiv_set_rate(struct clk_hw *hw, unsigned long rate,
+					       unsigned long parent_rate)
+{
+	struct clk_alpha_pll_postdiv *pll = to_clk_alpha_pll_postdiv(hw);
+	int i, val = 0, div, ret;
+	u32 mask;
+
+	/*
+	 * If the PLL is in FSM mode, then treat set_rate callback as a
+	 * no-operation.
+	 */
+	ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
+	if (ret)
+		return ret;
+
+	if (val & LUCID_5LPE_ENABLE_VOTE_RUN)
+		return 0;
+
+	div = DIV_ROUND_UP_ULL((u64)parent_rate, rate);
+	for (i = 0; i < pll->num_post_div; i++) {
+		if (pll->post_div_table[i].div == div) {
+			val = pll->post_div_table[i].val;
+			break;
+		}
+	}
+
+	mask = GENMASK(pll->width + pll->post_div_shift - 1, pll->post_div_shift);
+	return regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll),
+				  mask, val << pll->post_div_shift);
+}
+
+const struct clk_ops clk_alpha_pll_lucid_5lpe_ops = {
+	.prepare = alpha_pll_lucid_5lpe_prepare,
+	.enable = alpha_pll_lucid_5lpe_enable,
+	.disable = alpha_pll_lucid_5lpe_disable,
+	.is_enabled = clk_trion_pll_is_enabled,
+	.recalc_rate = clk_trion_pll_recalc_rate,
+	.round_rate = clk_alpha_pll_round_rate,
+	.set_rate = alpha_pll_lucid_5lpe_set_rate,
+};
+EXPORT_SYMBOL(clk_alpha_pll_lucid_5lpe_ops);
+
+const struct clk_ops clk_alpha_pll_fixed_lucid_5lpe_ops = {
+	.enable = alpha_pll_lucid_5lpe_enable,
+	.disable = alpha_pll_lucid_5lpe_disable,
+	.is_enabled = clk_trion_pll_is_enabled,
+	.recalc_rate = clk_trion_pll_recalc_rate,
+	.round_rate = clk_alpha_pll_round_rate,
+};
+EXPORT_SYMBOL(clk_alpha_pll_fixed_lucid_5lpe_ops);
+
+const struct clk_ops clk_alpha_pll_postdiv_lucid_5lpe_ops = {
+	.recalc_rate = clk_alpha_pll_postdiv_fabia_recalc_rate,
+	.round_rate = clk_alpha_pll_postdiv_fabia_round_rate,
+	.set_rate = clk_lucid_5lpe_pll_postdiv_set_rate,
+};
+EXPORT_SYMBOL(clk_alpha_pll_postdiv_lucid_5lpe_ops);
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index 0ea30d2f3da1..6943e933be0f 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -144,6 +144,10 @@ extern const struct clk_ops clk_alpha_pll_lucid_ops;
  extern const struct clk_ops clk_alpha_pll_postdiv_lucid_ops;
  extern const struct clk_ops clk_alpha_pll_agera_ops;
+extern const struct clk_ops clk_alpha_pll_lucid_5lpe_ops;
+extern const struct clk_ops clk_alpha_pll_fixed_lucid_5lpe_ops;
+extern const struct clk_ops clk_alpha_pll_postdiv_lucid_5lpe_ops;
+
  void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
  			     const struct alpha_pll_config *config);
  void clk_fabia_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,





[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux