Re: [PATCH 5/7] regulator: qcom-labibb: Implement short-circuit and over-current IRQs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Il 11/01/21 20:23, AngeloGioacchino Del Regno ha scritto:
Il 11/01/21 20:14, AngeloGioacchino Del Regno ha scritto:
Il 11/01/21 14:57, Mark Brown ha scritto:
On Sat, Jan 09, 2021 at 02:29:19PM +0100, AngeloGioacchino Del Regno wrote:

+    /* If the regulator is not enabled, this is a fake event */
+    if (!ops->is_enabled(vreg->rdev))
+        return 0;

Or handling the interrupt raced with a disable initiated from elsewhere.
Does the hardware actually have a problem with reporting spurious errors?

Sorry, I forgot to answer to this one in the previous email.

Yes, apparently the hardware has this issue: when the current draw is very high and you disable the regulator while the attached device is still drawing a lot of current (like on the Xperia XZ2 smartphone, but I don't want to comment on that phone's HW quirks...) then the OCP interrupt fires *after* disabling the LAB/IBB regulators.

This doesn't seem to happen if the current draw is low in the exact moment the regulator gets disabled, but that's not always possible since it depends on external HW design / board design sometimes...


+    return ret ? IRQ_NONE : IRQ_HANDLED;

Here and elsewhere please write normal conditional statements to improve
legibility.

No problem. Will do.

+    /* This function should be called only once, anyway. */
+    if (unlikely(vreg->ocp_irq_requested))
+        return 0;

If this is not a fast path it doesn't need an unlikely() annotation;
indeed it sounds more like there should be a warning printed if this
isn't supposed to be called multiple times.

That was extra-paranoid safety, looking at this one again, that should be totally unnecessary. I think that removing this check entirely would be just fine also because.. anyway.. writing to these registers more than once won't do any harm, nor break functionality: I mean, even if it happens for whatever reason, there's *no real need* to avoid it from the hw perspective.

+    /* IRQ polarities - LAB: trigger-low, IBB: trigger-high */
+    if (vreg->type == QCOM_LAB_TYPE) {
+        irq_flags |= IRQF_TRIGGER_LOW;
+        irq_trig_low = 1;
+    } else {
+        irq_flags |= IRQF_TRIGGER_HIGH;
+        irq_trig_low = 0;
+    }

This would be more clearly written as a switch statement.

A switch statement looked like being a bit "too much" for just two cases where vreg->type cannot be anything else but QCOM_LAB_TYPE or QCOM_IBB_TYPE... but okay, let's write a switch statement in place of that.

+    return devm_request_threaded_irq(vreg->dev, vreg->ocp_irq, NULL,
+                     qcom_labibb_ocp_isr, irq_flags,
+                     ocp_irq_name, vreg);

Are you *sure* that devm_ is appropriate here and the interrupt handler
won't attempt to use things that will be deallocated before devm gets
round to freeing the interrupt?

Yeah, I'm definitely sure.

+        if (!!(val & LABIBB_CONTROL_ENABLE)) {

The !! is redundant here and makes things less clear.

My bad, I forgot to clean this one up before sending.

@@ -166,8 +560,37 @@ static int qcom_labibb_of_parse_cb(struct device_node *np,
                     struct regulator_config *config)
  {
      struct labibb_regulator *vreg = config->driver_data;
+    char *sc_irq_name;

I really, really wouldn't expect to see interrupts being requested in
the DT parsing callback - apart from anything else the device is going
to have the physical interrupts with or without DT binding information.
These callbacks are for regulator specific properties, not basic probing.
Just request the interrupts in the main probe function, this also means
you can avoid using all the DT specific APIs which are generally a
warning sign.


...And I even wrote a comment saying "The Short Circuit interrupt is critical: fail if not found"!!! Whoa! That was bad.
Yeah, I'm definitely moving that to the appropriate place.


I'm sorry for the triple e-mail... but I've just acknowledged that using platform_get_irq is actually impossible with the current schema. As you can see in the dt-bindings documentation, the driver is supposed to be declared in DT as

		labibb {

			compatible = "qcom,pmi8998-lab-ibb";



			ibb: ibb {

				interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>,

					     <0x3 0xdc 0x0 IRQ_TYPE_LEVEL_HIGH>;

				interrupt-names = "sc-err", "ocp";

			};



			lab: lab {

				interrupts = <0x3 0xde 0x1 IRQ_TYPE_EDGE_RISING>,

					     <0x3 0xde 0x0 IRQ_TYPE_LEVEL_LOW>;

				interrupt-names = "sc-err", "ocp";

			};

		};

...which was already a requirement before I touched it.
Now, this leaves two options here:
1. Keep the of_get_irq way, or
2. Move the interrupts, change the documentation (currently, only pmi8998.dtsi) and also fix pmi8998.dtsi to reflect the new changes.

I am asking before proceeding because I know that changing a schema that is already set sometimes gets "negated".

How should I proceed?

-- Angelo



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux