Re: [PATCH] interconnect: qcom: qcs404: Remove gpu and display nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 11/11/2020 2:07 AM, Georgi Djakov wrote:
The following errors are noticed during boot on a QCS404 board:
[    2.926647] qcom_icc_rpm_smd_send mas 6 error -6
[    2.934573] qcom_icc_rpm_smd_send mas 8 error -6

These errors show when we try to configure the GPU and display nodes,
which are defined in the topology, but these hardware blocks actually
do not exist on QCS404. According to the datasheet, GPU and display
are only present on QCS405 and QCS407.

Even on QCS405/407 where GPU and display are present, you'd still get these errors since these particular nodes aren't supported on RPM and are purely local. Instead of removing these we should just change their mas_rpm_id to -1. It's harmless to leave them in for QCS404 since they're only used for path aggregation. The same code can support all variants of the QCS400 series. We just wouldn't expect anyone to actually vote these paths on QCS404. Similar to how the gcc-qcs404 clock provider still registers the GPU and MDP clocks.


Signed-off-by: Georgi Djakov <georgi.djakov@xxxxxxxxxx>
---
  drivers/interconnect/qcom/qcs404.c | 9 +++------
  1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/drivers/interconnect/qcom/qcs404.c b/drivers/interconnect/qcom/qcs404.c
index 9f992422e92f..2ed544e23ff3 100644
--- a/drivers/interconnect/qcom/qcs404.c
+++ b/drivers/interconnect/qcom/qcs404.c
@@ -20,8 +20,6 @@
enum {
  	QCS404_MASTER_AMPSS_M0 = 1,
-	QCS404_MASTER_GRAPHICS_3D,
-	QCS404_MASTER_MDP_PORT0,
  	QCS404_SNOC_BIMC_1_MAS,
  	QCS404_MASTER_TCU_0,
  	QCS404_MASTER_SPDM,
@@ -156,8 +154,6 @@ struct qcom_icc_desc {
  	}
DEFINE_QNODE(mas_apps_proc, QCS404_MASTER_AMPSS_M0, 8, 0, -1, QCS404_SLAVE_EBI_CH0, QCS404_BIMC_SNOC_SLV);
-DEFINE_QNODE(mas_oxili, QCS404_MASTER_GRAPHICS_3D, 8, 6, -1, QCS404_SLAVE_EBI_CH0, QCS404_BIMC_SNOC_SLV);
-DEFINE_QNODE(mas_mdp, QCS404_MASTER_MDP_PORT0, 8, 8, -1, QCS404_SLAVE_EBI_CH0, QCS404_BIMC_SNOC_SLV > DEFINE_QNODE(mas_snoc_bimc_1, QCS404_SNOC_BIMC_1_MAS, 8, 76, -1,
QCS404_SLAVE_EBI_CH0);
  DEFINE_QNODE(mas_tcu_0, QCS404_MASTER_TCU_0, 8, -1, -1, QCS404_SLAVE_EBI_CH0, QCS404_BIMC_SNOC_SLV);
  DEFINE_QNODE(mas_spdm, QCS404_MASTER_SPDM, 4, -1, -1, QCS404_PNOC_INT_3);
@@ -231,8 +227,6 @@ DEFINE_QNODE(slv_lpass, QCS404_SLAVE_LPASS, 4, -1, -1, 0);
static struct qcom_icc_node *qcs404_bimc_nodes[] = {
  	[MASTER_AMPSS_M0] = &mas_apps_proc,
-	[MASTER_OXILI] = &mas_oxili,
-	[MASTER_MDP_PORT0] = &mas_mdp,
  	[MASTER_SNOC_BIMC_1] = &mas_snoc_bimc_1,
  	[MASTER_TCU_0] = &mas_tcu_0,
  	[SLAVE_EBI_CH0] = &slv_ebi,
@@ -460,6 +454,9 @@ static int qnoc_probe(struct platform_device *pdev)
  	for (i = 0; i < num_nodes; i++) {
  		size_t j;
+ if (!qnodes[i])
+			continue;
+
  		node = icc_node_create(qnodes[i]->id);
  		if (IS_ERR(node)) {
  			ret = PTR_ERR(node);




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux