On Fri, 30 Oct 2020 at 09:14, Manivannan Sadhasivam
<manivannan.sadhasivam@xxxxxxxxxx> wrote:
>
> Hi Loic,
>
> On Wed, Oct 28, 2020 at 05:34:58PM +0100, Loic Poulain wrote:
> > This patch adds a new network driver implementing MHI transport for
> > network packets. Packets can be in any format, though QMAP (rmnet)
> > is the usual protocol (flow control + PDN mux).
> >
> > It support two MHI devices, IP_HW0 which is, the path to the IPA
> > (IP accelerator) on qcom modem, And IP_SW0 which is the software
> > driven IP path (to modem CPU).
> >
>
> This patch looks good to me. I just commented few nits inline. With those
> addressed, you can have my:
>
> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
Thanks for your review Mani, going to address that points in v9.
>
> Thanks,
> Mani
>
> > Signed-off-by: Loic Poulain <loic.poulain@xxxxxxxxxx>
> > ---
> > v2: - rebase on net-next
> > - remove useless skb_linearize
> > - check error type on mhi_queue return
> > - rate limited errors
> > - Schedule RX refill only on 'low' buf level
> > - SET_NETDEV_DEV in probe
> > - reorder device remove sequence
> > v3: - Stop channels on net_register error
> > - Remove useles parentheses
> > - Add driver .owner
> > v4: - prevent potential cpu hog in rx-refill loop
> > - Access mtu via READ_ONCE
> > v5: - Fix access to u64 stats
> > v6: - Stop TX queue earlier if queue is full
> > - Preventing 'abnormal' NETDEV_TX_BUSY path
> > v7: - Stop dl/ul cb operations on channel resetting
> > v8: - remove premature comment about TX threading gain
> > - check rx_queued to determine queuing limits
> > - fix probe error path (unified goto usage)
> >
> > drivers/net/Kconfig | 7 ++
> > drivers/net/Makefile | 1 +
> > drivers/net/mhi_net.c | 313 ++++++++++++++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 321 insertions(+)
> > create mode 100644 drivers/net/mhi_net.c
> >
> > diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
> > index 1368d1d..11a6357 100644
> > --- a/drivers/net/Kconfig
> > +++ b/drivers/net/Kconfig
> > @@ -426,6 +426,13 @@ config VSOCKMON
> > mostly intended for developers or support to debug vsock issues. If
> > unsure, say N.
> >
> > +config MHI_NET
> > + tristate "MHI network driver"
> > + depends on MHI_BUS
> > + help
> > + This is the network driver for MHI. It can be used with
>
> network driver for MHI bus.
>
> > + QCOM based WWAN modems (like SDX55). Say Y or M.
> > +
> > endif # NET_CORE
> >
> > config SUNGEM_PHY
> > diff --git a/drivers/net/Makefile b/drivers/net/Makefile
> > index 94b6080..8312037 100644
> > --- a/drivers/net/Makefile
> > +++ b/drivers/net/Makefile
> > @@ -34,6 +34,7 @@ obj-$(CONFIG_GTP) += gtp.o
> > obj-$(CONFIG_NLMON) += nlmon.o
> > obj-$(CONFIG_NET_VRF) += vrf.o
> > obj-$(CONFIG_VSOCKMON) += vsockmon.o
> > +obj-$(CONFIG_MHI_NET) += mhi_net.o
> >
> > #
> > # Networking Drivers
> > diff --git a/drivers/net/mhi_net.c b/drivers/net/mhi_net.c
> > new file mode 100644
> > index 0000000..4ba146d
> > --- /dev/null
> > +++ b/drivers/net/mhi_net.c
> > @@ -0,0 +1,313 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/* MHI Network driver - Network over MHI
>
> Network over MHI bus.
>
> > + *
> > + * Copyright (C) 2020 Linaro Ltd <loic.poulain@xxxxxxxxxx>
> > + */
> > +
> > +#include <linux/if_arp.h>
> > +#include <linux/mhi.h>
> > +#include <linux/mod_devicetable.h>
> > +#include <linux/module.h>
> > +#include <linux/netdevice.h>
> > +#include <linux/skbuff.h>
> > +#include <linux/u64_stats_sync.h>
> > +
> > +#define MIN_MTU ETH_MIN_MTU
> > +#define MAX_MTU 0xffff
> > +#define DEFAULT_MTU 16384
>
> Please add a prefix to avoid namespace issues in future...
>
> > +
> > +struct mhi_net_stats {
> > + u64_stats_t rx_packets;
> > + u64_stats_t rx_bytes;
> > + u64_stats_t rx_errors;
> > + u64_stats_t rx_dropped;
> > + u64_stats_t tx_packets;
> > + u64_stats_t tx_bytes;
> > + u64_stats_t tx_errors;
> > + u64_stats_t tx_dropped;
> > + atomic_t rx_queued;
> > + struct u64_stats_sync tx_syncp;
> > + struct u64_stats_sync rx_syncp;
> > +};
> > +
> > +struct mhi_net_dev {
> > + struct mhi_device *mdev;
> > + struct net_device *ndev;
> > + struct delayed_work rx_refill;
> > + struct mhi_net_stats stats;
> > + u32 rx_queue_sz;
> > +};
> > +
>
> [...]
>
> > +static void mhi_net_rx_refill_work(struct work_struct *work)
> > +{
> > + struct mhi_net_dev *mhi_netdev = container_of(work, struct mhi_net_dev,
> > + rx_refill.work);
> > + struct net_device *ndev = mhi_netdev->ndev;
> > + struct mhi_device *mdev = mhi_netdev->mdev;
> > + int size = READ_ONCE(ndev->mtu);
> > + struct sk_buff *skb;
> > + int err;
> > +
> > + do {
> > + skb = netdev_alloc_skb(ndev, size);
> > + if (unlikely(!skb))
> > + break;
> > +
> > + err = mhi_queue_skb(mdev, DMA_FROM_DEVICE, skb, size, MHI_EOT);
> > + if (unlikely(err)) {
> > + net_err_ratelimited("%s: Failed to queue RX buf (%d)\n",
> > + ndev->name, err);
> > + kfree_skb(skb);
> > + break;
> > + }
> > +
> > + /* Do not hog the CPU if rx buffers are completed faster than
> > + * queued (unlikely).
>
> s/completed/consumed
>
> > + */
> > + cond_resched();
> > + } while (atomic_inc_return(&mhi_netdev->stats.rx_queued) < mhi_netdev->rx_queue_sz);
> > +
> > + /* If we're still starved of rx buffers, reschedule later */
> > + if (unlikely(!atomic_read(&mhi_netdev->stats.rx_queued)))
> > + schedule_delayed_work(&mhi_netdev->rx_refill, HZ / 2);
> > +}
> > +
> > +static int mhi_net_probe(struct mhi_device *mhi_dev,
> > + const struct mhi_device_id *id)
> > +{
> > + const char *netname = (char *)id->driver_data;
> > + struct mhi_net_dev *mhi_netdev;
> > + struct net_device *ndev;
> > + struct device *dev = &mhi_dev->dev;
> > + int err;
>
> Since this is a networking driver, please stick to reverse xmas tree order for
> local variables.
