On Thu, Oct 08, 2020 at 11:03:42PM +0530, gokulsri@xxxxxxxxxxxxxx wrote:
> On 2020-10-08 18:41, Manivannan Sadhasivam wrote:
> > Hi,
> >
> > On Thu, Oct 08, 2020 at 06:02:24PM +0530, Gokul Sriram Palanisamy wrote:
> > > Enabled MHI device support over PCIe and added memory
> > > reservation required for MHI enabled QCN9000 PCIe card.
> > >
> > > Signed-off-by: Gokul Sriram Palanisamy <gokulsri@xxxxxxxxxxxxxx>
> > > ---
> > > arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi | 47
> > > ++++++++++++++++++++++++++++++
> > > 1 file changed, 47 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
> > > b/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
> > > index 0827055..e5c1ec0 100644
> > > --- a/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
[...]
> > > + pcie0_rp: pcie0_rp {
> > > + reg = <0 0 0 0 0>;
> > > +
> > > + status = "ok";
> > > + mhi_0: qcom,mhi@0 {
> >
> > MHI doesn't support devicetree as of now so how is this supposed to
> > work?
> > Have you tested this series with mainline?
> >
> > Thanks,
> > Mani
> >
>
> Hi Mani,
> This node entries will be consumed by ath11k driver and is not supposed to
> be consumed by mhi driver.
> And yes, it is tested on Mainline.
>
Can you please point me to the relevant binding or the code which consumes this
change?
Also please explain what it does! For enabling MHI support over PCIe you don't
need this node at all. You just need to define the PCIe device ID in the ath11k
driver and that's it.
Adding Kalle to this thread...
Thanks,
Mani
> Regards,
> Gokul
>
> > > + reg = <0 0 0 0 0 >;
> > > +
> > > + qrtr_instance_id = <0x20>;
> > > + base-addr = <0x50f00000>;
> > > + m3-dump-addr = <0x53c00000>;
> > > + etr-addr = <0x53d00000>;
> > > + qcom,caldb-addr = <0x53e00000>;
> > > + };
> > > + };
> > > };
> > >
> > > &pcie1 {
> > > status = "ok";
> > > perst-gpio = <&tlmm 61 0x1>;
> > > +
> > > + pcie1_rp: pcie1_rp {
> > > + reg = <0 0 0 0 0>;
> > > +
> > > + status = "ok";
> > > + mhi_1: qcom,mhi@1 {
> > > + reg = <0 0 0 0 0 >;
> > > +
> > > + qrtr_instance_id = <0x21>;
> > > + base-addr = <0x54600000>;
> > > + m3-dump-addr = <0x57300000>;
> > > + etr-addr = <0x57400000>;
> > > + qcom,caldb-addr = <0x57500000>;
> > > + };
> > > + };
> > > + };
> > > };
> > >
> > > &qmp_pcie_phy0 {
> > > --
> > > 2.7.4
> > >
