Re: [PATCH v2 4/4] arm: dts: add 8devices Habanero DVK

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Sep 9, 2020 at 9:56 PM Robert Marko <robert.marko@xxxxxxxxxx> wrote:
>
> 8devices Habanero DVK is a dual-band SoM development kit based on Qualcomm
> IPQ4019 + QCA8075 platform.
>
> Specs are:
> CPU: QCA IPQ4019
> RAM: DDR3L 512MB
> Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
> WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
> WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
> Ethernet: 5x Gbit LAN (QCA 8075)
> USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
> MicroSD slot (Uses SD controller built into IPQ4019)
> SDIO3.0/EMMC slot (Uses the same SD controller)
> Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
> 5x LEDs (4 GPIO controllable)
> 2x Pushbutton (1 is connected to GPIO, other to SoC reset)
> LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
> 1x UART 115200 rate on J18
>
> 2x breakout development headers
> 12V DC Jack for power
> DIP switch for bootstrap configuration
>
> Signed-off-by: Robert Marko <robert.marko@xxxxxxxxxx>
> Cc: Luka Perkov <luka.perkov@xxxxxxxxxx>
> ---
> Changes since v1:
> * Drop include that does not exist
>
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../boot/dts/qcom-ipq4019-habanero-dvk.dts    | 304 ++++++++++++++++++
>  2 files changed, 305 insertions(+)
>  create mode 100644 arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 246d82fc5fcd..004262e0d699 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -898,6 +898,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
>         qcom-ipq4019-ap.dk04.1-c3.dtb \
>         qcom-ipq4019-ap.dk07.1-c1.dtb \
>         qcom-ipq4019-ap.dk07.1-c2.dtb \
> +       qcom-ipq4019-habanero-dvk.dtb \
>         qcom-ipq8064-ap148.dtb \
>         qcom-ipq8064-rb3011.dtb \
>         qcom-msm8660-surf.dtb \
> diff --git a/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts
> new file mode 100644
> index 000000000000..fe054adda0a7
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts
> @@ -0,0 +1,304 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/* Copyright (c) 2019, Robert Marko <robimarko@xxxxxxxxx> */
> +
> +#include "qcom-ipq4019.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +       model = "8devices Habanero DVK";
> +       compatible = "8dev,habanero-dvk";
> +
> +       keys {
> +               compatible = "gpio-keys";
> +
> +               reset {
> +                       label = "reset";
> +                       gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
> +                       linux,code = <KEY_RESTART>;
> +               };
> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +
> +               led_status: status {
> +                       label = "habanero-dvk:green:status";
> +                       gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
> +                       panic-indicator;
> +               };
> +
> +               led_upgrade: upgrade {
> +                       label = "habanero-dvk:green:upgrade";
> +                       gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
> +               };
> +
> +               wlan2g {
> +                       label = "habanero-dvk:green:wlan2g";
> +                       gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
> +                       linux,default-trigger = "phy0tpt";
> +               };
> +
> +               wlan5g {
> +                       label = "habanero-dvk:green:wlan5g";
> +                       gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
> +                       linux,default-trigger = "phy1tpt";
> +               };
> +       };
> +};
> +
> +&vqmmc {
> +       status = "okay";
> +};
> +
> +&sdhci {
> +       status = "okay";
> +
> +       pinctrl-0 = <&sd_pins>;
> +       pinctrl-names = "default";
> +       cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
> +       vqmmc-supply = <&vqmmc>;
> +};
> +
> +&qpic_bam {
> +       status = "okay";
> +};
> +
> +&tlmm {
> +       mdio_pins: mdio_pinmux {
> +               mux_1 {
> +                       pins = "gpio6";
> +                       function = "mdio";
> +                       bias-pull-up;
> +               };
> +
> +               mux_2 {
> +                       pins = "gpio7";
> +                       function = "mdc";
> +                       bias-pull-up;
> +               };
> +       };
> +
> +       serial_pins: serial_pinmux {
> +               mux {
> +                       pins = "gpio16", "gpio17";
> +                       function = "blsp_uart0";
> +                       bias-disable;
> +               };
> +       };
> +
> +       spi_0_pins: spi_0_pinmux {
> +               pinmux {
> +                       function = "blsp_spi0";
> +                       pins = "gpio13", "gpio14", "gpio15";
> +                       drive-strength = <12>;
> +                       bias-disable;
> +               };
> +
> +               pinmux_cs {
> +                       function = "gpio";
> +                       pins = "gpio12";
> +                       drive-strength = <2>;
> +                       bias-disable;
> +                       output-high;
> +               };
> +       };
> +
> +       nand_pins: nand_pins {
> +               pullups {
> +                       pins =  "gpio52", "gpio53", "gpio58", "gpio59";
> +                       function = "qpic";
> +                       bias-pull-up;
> +               };
> +
> +               pulldowns {
> +                       pins = "gpio54", "gpio55", "gpio56", "gpio57",
> +                               "gpio60", "gpio62", "gpio63", "gpio64",
> +                               "gpio65", "gpio66", "gpio67", "gpio68",
> +                               "gpio69";
> +                       function = "qpic";
> +                       bias-pull-down;
> +               };
> +       };
> +
> +       sd_pins: sd_pins {
> +               pinmux {
> +                       function = "sdio";
> +                       pins = "gpio23", "gpio24", "gpio25", "gpio26",
> +                               "gpio28", "gpio29", "gpio30", "gpio31";
> +                       drive-strength = <10>;
> +               };
> +
> +               pinmux_sd_clk {
> +                       function = "sdio";
> +                       pins = "gpio27";
> +                       drive-strength = <16>;
> +               };
> +
> +               pinmux_sd7 {
> +                       function = "sdio";
> +                       pins = "gpio32";
> +                       drive-strength = <10>;
> +                       bias-disable;
> +               };
> +       };
> +};
> +
> +&watchdog {
> +       status = "okay";
> +};
> +
> +&prng {
> +       status = "okay";
> +};
> +
> +&blsp_dma {
> +       status = "okay";
> +};
> +
> +&blsp1_spi1 {
> +       status = "okay";
> +
> +       pinctrl-0 = <&spi_0_pins>;
> +       pinctrl-names = "default";
> +       cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
> +
> +       flash@0 {
> +               compatible = "jedec,spi-nor";
> +               spi-max-frequency = <24000000>;
> +               reg = <0>;
> +
> +               partitions {
> +                       compatible = "fixed-partitions";
> +                       #address-cells = <1>;
> +                       #size-cells = <1>;
> +
> +                       partition@0 {
> +                               label = "SBL1";
> +                               reg = <0x00000000 0x00040000>;
> +                               read-only;
> +                       };
> +                       partition@40000 {
> +                               label = "MIBIB";
> +                               reg = <0x00040000 0x00020000>;
> +                               read-only;
> +                       };
> +                       partition@60000 {
> +                               label = "QSEE";
> +                               reg = <0x00060000 0x00060000>;
> +                               read-only;
> +                       };
> +                       partition@c0000 {
> +                               label = "CDT";
> +                               reg = <0x000c0000 0x00010000>;
> +                               read-only;
> +                       };
> +                       partition@d0000 {
> +                               label = "DDRPARAMS";
> +                               reg = <0x000d0000 0x00010000>;
> +                               read-only;
> +                       };
> +                       partition@e0000 {
> +                               label = "APPSBLENV"; /* uboot env */
> +                               reg = <0x000e0000 0x00010000>;
> +                               read-only;
> +                       };
> +                       partition@f0000 {
> +                               label = "APPSBL"; /* uboot */
> +                               reg = <0x000f0000 0x00080000>;
> +                               read-only;
> +                       };
> +                       partition@170000 {
> +                               label = "ART";
> +                               reg = <0x00170000 0x00010000>;
> +                               read-only;
> +                       };
> +                       partition@180000 {
> +                               label = "cfg";
> +                               reg = <0x00180000 0x00040000>;
> +                       };
> +                       partition@1c0000 {
> +                               label = "firmware";
> +                               compatible = "denx,fit";
> +                               reg = <0x001c0000 0x01e40000>;
> +                       };
> +               };
> +       };
> +};
> +
> +/* Some DVK boards ship without NAND */
> +&nand {
> +       status = "okay";
> +
> +       pinctrl-0 = <&nand_pins>;
> +       pinctrl-names = "default";
> +};
> +
> +&blsp1_uart1 {
> +       status = "okay";
> +
> +       pinctrl-0 = <&serial_pins>;
> +       pinctrl-names = "default";
> +};
> +
> +&cryptobam {
> +       status = "okay";
> +};
> +
> +&crypto {
> +       status = "okay";
> +};
> +
> +&mdio {
> +       status = "okay";
> +
> +       pinctrl-0 = <&mdio_pins>;
> +       pinctrl-names = "default";
> +};
> +
> +&pcie0 {
> +       status = "okay";
> +
> +       perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
> +       wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
> +
> +       /* Free slot for use */
> +       bridge@0,0 {
> +               reg = <0x00000000 0 0 0 0>;
> +               #address-cells = <3>;
> +               #size-cells = <2>;
> +               ranges;
> +       };
> +};
> +
> +&wifi0 {
> +       status = "okay";
> +
> +       qcom,ath10k-calibration-variant = "8devices-Habanero";
> +};
> +
> +&wifi1 {
> +       status = "okay";
> +
> +       qcom,ath10k-calibration-variant = "8devices-Habanero";
> +};
> +
> +&usb3_ss_phy {
> +       status = "okay";
> +};
> +
> +&usb3_hs_phy {
> +       status = "okay";
> +};
> +
> +&usb3 {
> +       status = "okay";
> +};
> +
> +&usb2_hs_phy {
> +       status = "okay";
> +};
> +
> +&usb2 {
> +       status = "okay";
> +};
> --
> 2.26.2
>

Hi,
Is there an issue with the patch preventing the review?

Regards,
Robert



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux