Re: [PATCH 2/3] spi: spi-geni-qcom: Don't program CS_TOGGLE again and again

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sat 12 Sep 16:08 CDT 2020, Douglas Anderson wrote:

> We always toggle the chip select manually in spi-geni-qcom so that we
> can properly implement the Linux API.  There's no reason to program
> this to the hardware on every transfer.  Program it once at init and
> be done with it.
> 
> This saves some part of a microsecond of overhead on each transfer.
> While not really noticeable on any real world benchmarks, we might as
> well save the time.
> 

Reviewed-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>

Regards,
Bjorn

> Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
> ---
> 
>  drivers/spi/spi-geni-qcom.c | 12 +++++++-----
>  1 file changed, 7 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
> index 7f0bf0dec466..92d88bf85a90 100644
> --- a/drivers/spi/spi-geni-qcom.c
> +++ b/drivers/spi/spi-geni-qcom.c
> @@ -290,6 +290,7 @@ static int spi_geni_init(struct spi_geni_master *mas)
>  {
>  	struct geni_se *se = &mas->se;
>  	unsigned int proto, major, minor, ver;
> +	u32 spi_tx_cfg;
>  
>  	pm_runtime_get_sync(mas->dev);
>  
> @@ -322,6 +323,11 @@ static int spi_geni_init(struct spi_geni_master *mas)
>  
>  	geni_se_select_mode(se, GENI_SE_FIFO);
>  
> +	/* We always control CS manually */
> +	spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
> +	spi_tx_cfg &= ~CS_TOGGLE;
> +	writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
> +
>  	pm_runtime_put(mas->dev);
>  	return 0;
>  }
> @@ -331,7 +337,7 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
>  				u16 mode, struct spi_master *spi)
>  {
>  	u32 m_cmd = 0;
> -	u32 spi_tx_cfg, len;
> +	u32 len;
>  	struct geni_se *se = &mas->se;
>  	int ret;
>  
> @@ -350,7 +356,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
>  	spin_lock_irq(&mas->lock);
>  	spin_unlock_irq(&mas->lock);
>  
> -	spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
>  	if (xfer->bits_per_word != mas->cur_bits_per_word) {
>  		spi_setup_word_len(mas, mode, xfer->bits_per_word);
>  		mas->cur_bits_per_word = xfer->bits_per_word;
> @@ -364,8 +369,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
>  	mas->tx_rem_bytes = 0;
>  	mas->rx_rem_bytes = 0;
>  
> -	spi_tx_cfg &= ~CS_TOGGLE;
> -
>  	if (!(mas->cur_bits_per_word % MIN_WORD_LEN))
>  		len = xfer->len * BITS_PER_BYTE / mas->cur_bits_per_word;
>  	else
> @@ -384,7 +387,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
>  		writel(len, se->base + SE_SPI_RX_TRANS_LEN);
>  		mas->rx_rem_bytes = xfer->len;
>  	}
> -	writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
>  
>  	/*
>  	 * Lock around right before we start the transfer since our
> -- 
> 2.28.0.618.gf4bc123cb7-goog
> 



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux