At the moment, clk-smd-rpm forces all clocks on at probe time (for "handoff"). However, it does not make the clk core aware of that. This means that the clocks stay enabled forever if they are not used by anything. We can easily disable them again after bootup has been completed, by making the clk core aware of the state. This is implemented by returning the current state of the clock in is_prepared(). Checking the SPMI clock registers reveals that this allows the RPM to disable unused BB/RF clocks. For example, on MSM8916 with all remote processors (except RPM) disabled, we get: +--------------------------+------------+---------+--------+-------+ | | BOOTLOADER | HANDOFF | BEFORE | AFTER | +--------------------------+------------+---------+--------+-------+ | BB_CLK1_STATUS1 (0x5108) | ON* | ON | ON | ON* | | BB_CLK2_STATUS1 (0x5208) | OFF | ON | ON | OFF | | RF_CLK1_STATUS1 (0x5408) | OFF | ON | ON | OFF | | RF_CLK2_STATUS1 (0x5508) | OFF | ON | ON | OFF | +--------------------------+------------+---------+--------+-------+ * BB_CLK1 seems to be always-on in RPM on MSM8916 where: - BOOTLOADER = clk-smd-rpm disabled entirely in device tree - HANDOFF = temporarily after clk-smd-rpm was probed - BEFORE/AFTER = after boot without/with the changes in this commit With this commit BB_CLK2/RF_CLK1/RF_CLK2 are disabled again when unused. Cc: Georgi Djakov <georgi.djakov@xxxxxxxxxx> Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx> --- Originally I reported this here: https://lore.kernel.org/linux-arm-msm/20200523120810.GA166540@xxxxxxxxxxx/ Overall I'm not entirely sure why we need to force all these clocks on at all... But the downstream driver also seems to do it and the RPM interface is barely documented, so I didn't feel comfortable changing it... --- drivers/clk/qcom/clk-smd-rpm.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/drivers/clk/qcom/clk-smd-rpm.c b/drivers/clk/qcom/clk-smd-rpm.c index 0e1dfa89489e..fa960cb794a8 100644 --- a/drivers/clk/qcom/clk-smd-rpm.c +++ b/drivers/clk/qcom/clk-smd-rpm.c @@ -171,6 +171,9 @@ static int clk_smd_rpm_handoff(struct clk_smd_rpm *r) if (ret) return ret; + /* During handoff we force all clocks on */ + r->enabled = true; + return 0; } @@ -300,6 +303,13 @@ static void clk_smd_rpm_unprepare(struct clk_hw *hw) mutex_unlock(&rpm_smd_clk_lock); } +static int clk_smd_rpm_is_prepared(struct clk_hw *hw) +{ + struct clk_smd_rpm *r = to_clk_smd_rpm(hw); + + return r->enabled; +} + static int clk_smd_rpm_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) { @@ -396,6 +406,7 @@ static int clk_smd_rpm_enable_scaling(struct qcom_smd_rpm *rpm) static const struct clk_ops clk_smd_rpm_ops = { .prepare = clk_smd_rpm_prepare, .unprepare = clk_smd_rpm_unprepare, + .is_prepared = clk_smd_rpm_is_prepared, .set_rate = clk_smd_rpm_set_rate, .round_rate = clk_smd_rpm_round_rate, .recalc_rate = clk_smd_rpm_recalc_rate, @@ -404,6 +415,7 @@ static const struct clk_ops clk_smd_rpm_ops = { static const struct clk_ops clk_smd_rpm_branch_ops = { .prepare = clk_smd_rpm_prepare, .unprepare = clk_smd_rpm_unprepare, + .is_prepared = clk_smd_rpm_is_prepared, }; /* msm8916 */ -- 2.28.0
