Re: [PATCH v3 3/8] ASoC: qcom: lpass: Use regmap_field for i2sctl and dmactl registers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Thanks Srini for reviewing.

On 7/9/2020 2:56 PM, Srinivas Kandagatla wrote:


On 08/07/2020 06:08, Rohit kumar wrote:
I2SCTL and DMACTL registers has different bits alignment for newer
LPASS variants of SC7180 soc. Use REG_FIELD_ID() to define the
reg_fields in platform specific file and removed shifts and mask
macros for such registers from header file.

Signed-off-by: Rohit kumar <rohitkr@xxxxxxxxxxxxxx>

Thanks Rohit for doing this, this looks much better now!
I have few minor comments..

---
  sound/soc/qcom/lpass-apq8016.c   |  24 ++++++
  sound/soc/qcom/lpass-cpu.c       | 163 +++++++++++++++++++++++----------------
  sound/soc/qcom/lpass-ipq806x.c   |  24 ++++++
  sound/soc/qcom/lpass-lpaif-reg.h | 157 +++++++++++++++++++------------------   sound/soc/qcom/lpass-platform.c  | 151 +++++++++++++++++++++++++++---------
  sound/soc/qcom/lpass.h           |  53 +++++++++++++
  6 files changed, 398 insertions(+), 174 deletions(-)


index f0c7e93..f358d12 100644
--- a/sound/soc/qcom/lpass-cpu.c
+++ b/sound/soc/qcom/lpass-cpu.c
@@ -29,6 +29,32 @@
  #define LPASS_CPU_I2S_SD0_1_2_MASK    GENMASK(2, 0)
  #define LPASS_CPU_I2S_SD0_1_2_3_MASK    GENMASK(3, 0)


  static int lpass_cpu_daiops_set_sysclk(struct snd_soc_dai *dai, int clk_id,
          unsigned int freq, int dir)
  {
@@ -79,12 +105,13 @@ static int lpass_cpu_daiops_hw_params(struct snd_pcm_substream *substream,
          struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
  {
      struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai);
+    struct lpaif_i2sctl *i2sctl = drvdata->i2sctl;
+    unsigned int id = dai->driver->id;
      snd_pcm_format_t format = params_format(params);
      unsigned int channels = params_channels(params);
      unsigned int rate = params_rate(params);
      unsigned int mode;
-    unsigned int regval;
-    int bitwidth, ret;
+    int bitwidth, ret, regval;

Why is this change?

Sorry, It came as part of previous patchset. regval was removed in patchv2  and

bitwidth variable was used to configure both clk and i2sctl register, which was not proper.

Added regval again. I will repost this patch without this change.


        bitwidth = snd_pcm_format_width(format);
      if (bitwidth < 0) {
@@ -92,28 +119,45 @@ static int lpass_cpu_daiops_hw_params(struct snd_pcm_substream *substream,
          return bitwidth;
      }
  -    regval = LPAIF_I2SCTL_LOOPBACK_DISABLE |
-            LPAIF_I2SCTL_WSSRC_INTERNAL;
+    ret = regmap_fields_write(i2sctl->loopback, id,
+                 LPAIF_I2SCTL_LOOPBACK_DISABLE);
+    if (ret) {
+        dev_err(dai->dev, "error updating loopback field: %d\n", ret);
+        return ret;
+    }
+
+    ret = regmap_fields_write(i2sctl->wssrc, id,
+                 LPAIF_I2SCTL_WSSRC_INTERNAL);
+    if (ret) {
+        dev_err(dai->dev, "error updating wssrc field: %d\n", ret);
+        return ret;
+    }
        switch (bitwidth) {
      case 16:
-        regval |= LPAIF_I2SCTL_BITWIDTH_16;
+        regval = LPAIF_I2SCTL_BITWIDTH_16;
          break;
      case 24:
-        regval |= LPAIF_I2SCTL_BITWIDTH_24;
+        regval = LPAIF_I2SCTL_BITWIDTH_24;
          break;
      case 32:
-        regval |= LPAIF_I2SCTL_BITWIDTH_32;
+        regval = LPAIF_I2SCTL_BITWIDTH_32;
          break;
      default:
          dev_err(dai->dev, "invalid bitwidth given: %d\n", bitwidth);
          return -EINVAL;
      }
  +    ret = regmap_fields_write(i2sctl->bitwidth, id, regval);
+    if (ret) {
+        dev_err(dai->dev, "error updating bitwidth field: %d\n", ret);
+        return ret;
+    }
+
      if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
-        mode = drvdata->mi2s_playback_sd_mode[dai->driver->id];
+        mode = drvdata->mi2s_playback_sd_mode[id];
      else
-        mode = drvdata->mi2s_capture_sd_mode[dai->driver->id];
+        mode = drvdata->mi2s_capture_sd_mode[id];
        if (!mode) {
          dev_err(dai->dev, "no line is assigned\n");
@@ -175,30 +219,34 @@ static int lpass_cpu_daiops_hw_params(struct snd_pcm_substream *substream,
      }
        if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
-        regval |= LPAIF_I2SCTL_SPKMODE(mode);
+        ret = regmap_fields_write(i2sctl->spkmode, id,
+                     LPAIF_I2SCTL_SPKMODE(mode));
            if (channels >= 2)
-            regval |= LPAIF_I2SCTL_SPKMONO_STEREO;
+            ret = regmap_fields_write(i2sctl->spkmono, id,
+                         LPAIF_I2SCTL_SPKMONO_STEREO);
          else
-            regval |= LPAIF_I2SCTL_SPKMONO_MONO;
+            ret = regmap_fields_write(i2sctl->spkmono, id,
+                         LPAIF_I2SCTL_SPKMONO_MONO);
      } else {
-        regval |= LPAIF_I2SCTL_MICMODE(mode);
+        ret = regmap_fields_write(i2sctl->micmode, id,
+                     LPAIF_I2SCTL_MICMODE(mode));
            if (channels >= 2)
-            regval |= LPAIF_I2SCTL_MICMONO_STEREO;
+            ret = regmap_fields_write(i2sctl->micmono, id,
+                         LPAIF_I2SCTL_MICMONO_STEREO);
          else
-            regval |= LPAIF_I2SCTL_MICMONO_MONO;
+            ret = regmap_fields_write(i2sctl->micmono, id,
+                         LPAIF_I2SCTL_MICMONO_MONO);
      }
  -    ret = regmap_write(drvdata->lpaif_map,
-               LPAIF_I2SCTL_REG(drvdata->variant, dai->driver->id),
-               regval);
      if (ret) {
-        dev_err(dai->dev, "error writing to i2sctl reg: %d\n", ret);
+        dev_err(dai->dev, "error writing to i2sctl channels mode: %d\n",
+            ret);
          return ret;
      }
  -    ret = clk_set_rate(drvdata->mi2s_bit_clk[dai->driver->id],
+    ret = clk_set_rate(drvdata->mi2s_bit_clk[id],
                 rate * bitwidth * 2);
      if (ret) {
          dev_err(dai->dev, "error setting mi2s bitclk to %u: %d\n",
@@ -209,41 +257,24 @@ static int lpass_cpu_daiops_hw_params(struct snd_pcm_substream *substream,
      return 0;
  }
  -static int lpass_cpu_daiops_hw_free(struct snd_pcm_substream *substream,
-        struct snd_soc_dai *dai)
-{
-    struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai);
-    int ret;
-
-    ret = regmap_write(drvdata->lpaif_map,
-               LPAIF_I2SCTL_REG(drvdata->variant, dai->driver->id),
-               0);
-    if (ret)
-        dev_err(dai->dev, "error writing to i2sctl reg: %d\n", ret);
-
-    return ret;
-}

Any particular reason why this function remove

This was causing issue in playback/capture concurrency. It sets I2SCTL register value to 0

when usecase ends. However, playback/capture specific bits are already cleared during trigger() stop

function. So, this is not needed.

-
  static int lpass_cpu_daiops_prepare(struct snd_pcm_substream *substream,
          struct snd_soc_dai *dai)
  {
      struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai);
+    struct lpaif_i2sctl *i2sctl = drvdata->i2sctl;
+    unsigned int id = dai->driver->id;
      int ret;
-    unsigned int val, mask;
        if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
-        val = LPAIF_I2SCTL_SPKEN_ENABLE;
-        mask = LPAIF_I2SCTL_SPKEN_MASK;
-    } else  {
-        val = LPAIF_I2SCTL_MICEN_ENABLE;
-        mask = LPAIF_I2SCTL_MICEN_MASK;
+        ret = regmap_fields_write(i2sctl->spken, id,
+                     LPAIF_I2SCTL_SPKEN_ENABLE);
+    } else {
+        ret = regmap_fields_write(i2sctl->micen, id,
+                     LPAIF_I2SCTL_MICEN_ENABLE);
      }
  -    ret = regmap_update_bits(drvdata->lpaif_map,
-            LPAIF_I2SCTL_REG(drvdata->variant, dai->driver->id),
-            mask, val);
      if (ret)
-        dev_err(dai->dev, "error writing to i2sctl reg: %d\n", ret);
+        dev_err(dai->dev, "error writing to i2sctl enable: %d\n", ret);
        return ret;
  }
...
@@ -304,7 +326,6 @@ const struct snd_soc_dai_ops asoc_qcom_lpass_cpu_dai_ops = {
      .startup    = lpass_cpu_daiops_startup,
      .shutdown    = lpass_cpu_daiops_shutdown,
      .hw_params    = lpass_cpu_daiops_hw_params,
-    .hw_free    = lpass_cpu_daiops_hw_free,
      .prepare    = lpass_cpu_daiops_prepare,
      .trigger    = lpass_cpu_daiops_trigger,
  };
@@ -599,6 +620,18 @@ int asoc_qcom_lpass_cpu_platform_probe(struct platform_device *pdev)
          }
      }
  +    /* Allocation for i2sctl regmap fields */
+    drvdata->i2sctl = devm_kzalloc(&pdev->dev, sizeof(struct lpaif_i2sctl),
+                    GFP_KERNEL);
+
+    /* Initialize bitfields for dai I2SCTL register */
+    ret = lpass_cpu_init_i2sctl_bitfields(dev, drvdata->i2sctl,
+                        drvdata->lpaif_map);
+    if (ret) {
+        dev_err(dev, "error init i2sctl field: %d\n", ret);
+        return ret;
+    }
+
      ret = devm_snd_soc_register_component(dev,
                            &lpass_cpu_comp_driver,
                            variant->dai_driver,

diff --git a/sound/soc/qcom/lpass-lpaif-reg.h b/sound/soc/qcom/lpass-lpaif-reg.h
index 72a3e2f..5258e60 100644
--- a/sound/soc/qcom/lpass-lpaif-reg.h
+++ b/sound/soc/qcom/lpass-lpaif-reg.h
@@ -12,15 +12,12 @@
...
  #endif /* __LPASS_LPAIF_REG_H__ */
diff --git a/sound/soc/qcom/lpass-platform.c b/sound/soc/qcom/lpass-platform.c
index 34f7fd1..445ca193 100644
--- a/sound/soc/qcom/lpass-platform.c
+++ b/sound/soc/qcom/lpass-platform.c
@@ -50,6 +50,53 @@ static const struct snd_pcm_hardware lpass_platform_pcm_hardware = {
      .fifo_size        =    0,
  };
...
  static int lpass_platform_pcmops_open(struct snd_soc_component *component,
                        struct snd_pcm_substream *substream)
  {
@@ -59,9 +106,9 @@ static int lpass_platform_pcmops_open(struct snd_soc_component *component,       struct lpass_data *drvdata = snd_soc_component_get_drvdata(component);
      struct lpass_variant *v = drvdata->variant;
      int ret, dma_ch, dir = substream->stream;
-    struct lpass_pcm_data *data;
+    struct lpass_pcm_data *data = NULL;
  -    data = devm_kzalloc(soc_runtime->dev, sizeof(*data), GFP_KERNEL);
+    data = kzalloc(sizeof(*data), GFP_KERNEL);

Does this change belong in this patch?


As part of this change, I fixed memory leak too by adding kfree() in close()

However, this was causing issue as memory was allocated using devm_kzalloc().

Should I move it to different patch?


      if (!data)
          return -ENOMEM;
  @@ -111,13 +158,13 @@ static int lpass_platform_pcmops_close(struct snd_soc_component *component,
      struct snd_pcm_runtime *runtime = substream->runtime;
      struct lpass_data *drvdata = snd_soc_component_get_drvdata(component);
      struct lpass_variant *v = drvdata->variant;
-    struct lpass_pcm_data *data;
+    struct lpass_pcm_data *data = runtime->private_data;
  -    data = runtime->private_data;
      drvdata->substream[data->dma_ch] = NULL;
      if (v->free_dma_channel)
          v->free_dma_channel(drvdata, data->dma_ch);
  +    kfree(data);
      return 0;
  }
          return devm_snd_soc_register_component(&pdev->dev,
              &lpass_component_driver, NULL, 0);
diff --git a/sound/soc/qcom/lpass.h b/sound/soc/qcom/lpass.h
index 450020e..4294ec2 100644
--- a/sound/soc/qcom/lpass.h
+++ b/sound/soc/qcom/lpass.h
@@ -17,6 +17,28 @@
  #define LPASS_MAX_MI2S_PORTS            (8)
  #define LPASS_MAX_DMA_CHANNELS            (8)
...

  /* Both the CPU DAI and platform drivers will access this data */
  struct lpass_data {
  @@ -55,6 +77,10 @@ struct lpass_data {
      struct clk_bulk_data *clks;
      int num_clks;
  +    /* Regmap fields of I2SCTL & DMACTL registers bitfields */
+    struct lpaif_i2sctl *i2sctl;
+    struct lpaif_dmactl *rd_dmactl;
+    struct lpaif_dmactl *wr_dmactl;
  };
    /* Vairant data per each SOC */
@@ -72,6 +98,33 @@ struct lpass_variant {
      u32    wrdma_reg_stride;
      u32    wrdma_channels;

Above two along with rddma members can be removed, these become redundant after adding regmap field!

wrdma_channels is used in alloc_dma_channel() to get the channel id.

Also, both are used for other DMA registers such as LPAIF_RDMABASE_REG,

LPAIF_RDMABUFF_REG, LPAIF_RDMACURR_REG, etc.


+    /* I2SCTL Register fields */
+    struct reg_field loopback;
+    struct reg_field spken;
+    struct reg_field spkmode;
+    struct reg_field spkmono;
+    struct reg_field micen;
+    struct reg_field micmode;
+    struct reg_field micmono;
+    struct reg_field wssrc;
+    struct reg_field bitwidth;
+
+    /* RD_DMA Register fields */
+    struct reg_field rdma_bursten;
+    struct reg_field rdma_wpscnt;
+    struct reg_field rdma_intf;
+    struct reg_field rdma_fifowm;
+    struct reg_field rdma_enable;
+    struct reg_field rdma_dyncclk;
+
+    /* RD_DMA Register fields */
+    struct reg_field wrdma_bursten;
+    struct reg_field wrdma_wpscnt;
+    struct reg_field wrdma_intf;
+    struct reg_field wrdma_fifowm;
+    struct reg_field wrdma_enable;
+    struct reg_field wrdma_dyncclk;
+
      /**
       * on SOCs like APQ8016 the channel control bits start
       * at different offset to ipq806x

Thanks,

Rohit

--
Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a member
of the Code Aurora Forum, hosted by the Linux Foundation.




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux