[PATCH 1/3] spi: spi-geni-qcom: Avoid clock setting if not needed

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Every SPI transfer could have a different clock rate.  The
spi-geni-qcom controller code to deal with this was never very well
optimized and has always had a lot of code plus some calls into the
clk framework which, at the very least, would grab a mutex.  However,
until recently, the overhead wasn't _too_ much.  That changed with
commit 0e3b8a81f5df ("spi: spi-geni-qcom: Add interconnect support")
we're now calling geni_icc_set_bw(), which leads to a bunch of math
plus:
  geni_icc_set_bw()
    icc_set_bw()
      apply_constraints()
        qcom_icc_set()
          qcom_icc_bcm_voter_commit()
            rpmh_invalidate()
            rpmh_write_batch()
...and those rpmh commands can be a bit beefy if you call them too
often.

We already know what speed we were running at before, so if we see
that nothing has changed let's avoid the whole pile of code.

On my hardware, this made spi_geni_prepare_message() drop down from
~145 us down to ~14 us.

NOTE: Potentially it might also make sense to add some code into the
interconnect framework to avoid executing so much code when bandwidth
isn't changing, but even if we did that we still want to short circuit
here to save the extra math / clock calls.

Fixes: 0e3b8a81f5df ("spi: spi-geni-qcom: Add interconnect support")
Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
---

 drivers/spi/spi-geni-qcom.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
index e01c782ef7d0..bb4cdda2dec8 100644
--- a/drivers/spi/spi-geni-qcom.c
+++ b/drivers/spi/spi-geni-qcom.c
@@ -201,6 +201,9 @@ static int geni_spi_set_clock_and_bw(struct spi_geni_master *mas,
 	struct geni_se *se = &mas->se;
 	int ret;
 
+	if (clk_hz == mas->cur_speed_hz)
+		return 0;
+
 	ret = get_spi_clk_cfg(clk_hz, mas, &idx, &div);
 	if (ret) {
 		dev_err(mas->dev, "Err setting clk to %lu: %d\n", clk_hz, ret);
@@ -339,11 +342,9 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
 	}
 
 	/* Speed and bits per word can be overridden per transfer */
-	if (xfer->speed_hz != mas->cur_speed_hz) {
-		ret = geni_spi_set_clock_and_bw(mas, xfer->speed_hz);
-		if (ret)
-			return;
-	}
+	ret = geni_spi_set_clock_and_bw(mas, xfer->speed_hz);
+	if (ret)
+		return;
 
 	mas->tx_rem_bytes = 0;
 	mas->rx_rem_bytes = 0;
-- 
2.27.0.383.g050319c2ae-goog




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux