Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one and enable them on the MTP with appropriate firmware
defined.
Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 15 +++
arch/arm64/boot/dts/qcom/sm8250.dtsi | 116 ++++++++++++++++++++++++
2 files changed, 131 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 63d259931c4d..6894f8490dae 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -55,6 +55,11 @@ vreg_s6c_0p88: smpc6-regulator {
};
};
+&adsp {
+ status = "okay";
+ firmware-name = "qcom/sm8250/adsp.mbn";
+};
+
&apps_rsc {
pm8150-rpmh-regulators {
compatible = "qcom,pm8150-rpmh-regulators";
@@ -348,10 +353,20 @@ vreg_l7f_1p8: ldo7 {
};
};
+&cdsp {
+ status = "okay";
+ firmware-name = "qcom/sm8250/cdsp.mbn";
+};
+
&qupv3_id_1 {
status = "okay";
};
+&slpi {
+ status = "okay";
+ firmware-name = "qcom/sm8250/slpi.mbn";
+};
+
&tlmm {
gpio-reserved-ranges = <28 4>, <40 4>;
};
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 364d9a798673..a21299b9c62f 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -1052,6 +1052,83 @@ tcsr_mutex_regs: syscon@1f40000 {
reg = <0x0 0x01f40000 0x0 0x40000>;
};
+ slpi: remoteproc@5c00000 {
+ compatible = "qcom,sm8250-slpi-pas";
+ reg = <0 0x05c00000 0 0x4000>;
+
+ interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
+ <&rpmhpd SM8250_LCX>,
+ <&rpmhpd SM8250_LMX>;
+ power-domain-names = "load_state", "lcx", "lmx";
+
+ memory-region = <&slpi_mem>;
+
+ qcom,smem-states = <&smp2p_slpi_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_SLPI
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "lpass";
+ qcom,remote-pid = <3>;
+ };
+ };
+
+ cdsp: remoteproc@8300000 {
+ compatible = "qcom,sm8250-cdsp-pas";
+ reg = <0 0x08300000 0 0x10000>;
+
+ interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
+ <&rpmhpd SM8250_CX>;
+ power-domain-names = "load_state", "cx";
+
+ memory-region = <&cdsp_mem>;
+
+ qcom,smem-states = <&smp2p_cdsp_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_CDSP
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "lpass";
+ qcom,remote-pid = <5>;
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm8250-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
@@ -1668,6 +1745,45 @@ config {
};
};
+ adsp: remoteproc@17300000 {
+ compatible = "qcom,sm8250-adsp-pas";
+ reg = <0 0x17300000 0 0x100>;
+
+ interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "xo";
+
+ power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
+ <&rpmhpd SM8250_LCX>,
+ <&rpmhpd SM8250_LMX>;
+ power-domain-names = "load_state", "lcx", "lmx";
+
+ memory-region = <&adsp_mem>;
+
+ qcom,smem-states = <&smp2p_adsp_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_LPASS
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ label = "lpass";
+ qcom,remote-pid = <2>;
+ };
+ };
+
intc: interrupt-controller@17a00000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
--
2.26.2
