Re: [PATCH V7 6/7] spi: spi-qcom-qspi: Add interconnect support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Matthias,

On 5/26/2020 11:06 PM, Matthias Kaehlcke wrote:
On Tue, May 26, 2020 at 06:24:49PM +0530, Akash Asthana wrote:
Get the interconnect paths for QSPI device and vote according to the
current bus speed of the driver.

Signed-off-by: Akash Asthana <akashast@xxxxxxxxxxxxxx>
---
Changes in V2:
  - As per Bjorn's comment, introduced and using devm_of_icc_get API for getting
    path handle
  - As per Matthias comment, added error handling for icc_set_bw call

Changes in V3:
  - No Change.

Changes in V4:
  - As per Mark's comment move peak_bw guess as twice of avg_bw if
    nothing mentioned explicitly to ICC core.

Changes in V5:
  - Add icc_enable/disable to power on/off call.
  - Save some non-zero avg/peak value to ICC core by calling geni_icc_set_bw
    from probe so that when resume/icc_enable is called NOC are running at
    some non-zero value.

Changes in V6:
  - As per Matthias's comment made print statement consistent across driver

Changes in V7:
  - As per Matthias's comment removed usage of peak_bw variable because we don't
    have explicit peak requirement, we were voting peak = avg and this can be
    tracked using single variable for avg bw.
  - As per Matthias's comment improved print log.

  drivers/spi/spi-qcom-qspi.c | 57 ++++++++++++++++++++++++++++++++++++++++++++-
  1 file changed, 56 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-qcom-qspi.c b/drivers/spi/spi-qcom-qspi.c
index 3c4f83b..092ac27 100644
--- a/drivers/spi/spi-qcom-qspi.c
+++ b/drivers/spi/spi-qcom-qspi.c
@@ -2,6 +2,7 @@
  // Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
#include <linux/clk.h>
+#include <linux/interconnect.h>
  #include <linux/interrupt.h>
  #include <linux/io.h>
  #include <linux/module.h>
@@ -139,7 +140,9 @@ struct qcom_qspi {
  	struct device *dev;
  	struct clk_bulk_data *clks;
  	struct qspi_xfer xfer;
-	/* Lock to protect xfer and IRQ accessed registers */
+	struct icc_path *icc_path_cpu_to_qspi;
+	unsigned int avg_bw_cpu;
I should have noticed this earlier, but the field isn't needed now that
we have icc_enable/disable(). The bandwidth is set in
qcom_qspi_transfer_one() and that's it.

 From my side it would be fine to remove the field in a follow up patch,
to avoid respinning the series yet another time just for this.

Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>

I will resend patch V7 with the suggested change.

Thankyou for reviewing

Regards,

Akash

--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux