Re: [PATCH v7 2/4] usb: dwc3: qcom: Add interconnect support in dwc3 driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Quoting Sandeep Maheswaram (2020-03-31 22:15:43)
> diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
> index 1dfd024..d33ae86 100644
> --- a/drivers/usb/dwc3/dwc3-qcom.c
> +++ b/drivers/usb/dwc3/dwc3-qcom.c
> @@ -76,8 +85,13 @@ struct dwc3_qcom {
>         enum usb_dr_mode        mode;
>         bool                    is_suspended;
>         bool                    pm_suspended;
> +       struct icc_path         *usb_ddr_icc_path;
> +       struct icc_path         *apps_usb_icc_path;
>  };
>  
> +static int dwc3_qcom_interconnect_enable(struct dwc3_qcom *qcom);
> +static int dwc3_qcom_interconnect_disable(struct dwc3_qcom *qcom);

Please get rid of these. We shouldn't need forward declarations.

> +
>  static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
>  {
>         u32 reg;
> @@ -285,6 +307,101 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
>         return 0;
>  }
>  
> +
> +/**
> + * dwc3_qcom_interconnect_init() - Get interconnect path handles
> + * @qcom:                      Pointer to the concerned usb core.
> + *
> + */
> +static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom)
> +{
> +       struct device *dev = qcom->dev;
> +       int ret;
> +
> +       if (!device_is_bound(&qcom->dwc3->dev))
> +               return -EPROBE_DEFER;

How is this supposed to work? I see that this was added in an earlier
revision of this patch series but there isn't any mention of why
device_is_bound() is used here. It would be great if there was a comment
detailing why this is necessary. It sounds like maximum_speed is
important?

Furthermore, dwc3_qcom_interconnect_init() is called by
dwc3_qcom_probe() which is the function that registers the device for
qcom->dwc3->dev. If that device doesn't probe between the time it is
registered by dwc3_qcom_probe() and this function is called then we'll
fail dwc3_qcom_probe() with -EPROBE_DEFER. And that will remove the
qcom->dwc3->dev device from the platform bus because we call
of_platform_depopulate() on the error path of dwc3_qcom_probe().

So isn't this whole thing racy and can potentially lead us to a driver
probe loop where the wrapper (dwc3_qcom) and the core (dwc3) are probing
and we're trying to time it just right so that driver for dwc3 binds
before we setup interconnects? I don't know if dwc3 can communicate to
the wrapper but that would be more of a direct way to do this. Or maybe
the wrapper should try to read the DT property for maximum speed and
fallback to a worst case high bandwidth value if it can't figure it out
itself without help from dwc3 core.




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux