Re: R: [PATCH v3 09/11] PCI: qcom: add ipq8064 rev2 variant and set tx term offset

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 5/13/20 3:54 PM, ansuelsmth@xxxxxxxxx wrote:
>> Hi Ansuel,
>>
>> On 5/1/20 1:06 AM, Ansuel Smith wrote:
>>> From: Sham Muthayyan <smuthayy@xxxxxxxxxxxxxx>
>>>
>>> Add tx term offset support to pcie qcom driver need in some revision of
>>> the ipq806x SoC.
>>> Ipq8064 have tx term offset set to 7.
>>> Ipq8064-v2 revision and ipq8065 have the tx term offset set to 0.
>>>
>>> Signed-off-by: Sham Muthayyan <smuthayy@xxxxxxxxxxxxxx>
>>> Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
>>> ---
>>>  drivers/pci/controller/dwc/pcie-qcom.c | 15 +++++++++++++++
>>>  1 file changed, 15 insertions(+)
>>>
>>> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c
>> b/drivers/pci/controller/dwc/pcie-qcom.c
>>> index da8058fd1925..372d2c8508b5 100644
>>> --- a/drivers/pci/controller/dwc/pcie-qcom.c
>>> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
>>> @@ -45,6 +45,9 @@
>>>  #define PCIE_CAP_CPL_TIMEOUT_DISABLE		0x10
>>>
>>>  #define PCIE20_PARF_PHY_CTRL			0x40
>>> +#define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK	GENMASK(12,
>> 16)
>>
>> The mask definition is not correct. Should be GENMASK(20, 16)
>>
>>> +#define PHY_CTRL_PHY_TX0_TERM_OFFSET(x)		((x) << 16)
>>> +
>>>  #define PCIE20_PARF_PHY_REFCLK			0x4C
>>>  #define PHY_REFCLK_SSP_EN			BIT(16)
>>>  #define PHY_REFCLK_USE_PAD			BIT(12)
>>> @@ -118,6 +121,7 @@ struct qcom_pcie_resources_2_1_0 {
>>>  	u32 tx_swing_full;
>>>  	u32 tx_swing_low;
>>>  	u32 rx0_eq;
>>> +	u8 phy_tx0_term_offset;
>>>  };
>>>
>>>  struct qcom_pcie_resources_1_0_0 {
>>> @@ -318,6 +322,11 @@ static int
>> qcom_pcie_get_resources_2_1_0(struct qcom_pcie *pcie)
>>>  	if (IS_ERR(res->ext_reset))
>>>  		return PTR_ERR(res->ext_reset);
>>>
>>> +	if (of_device_is_compatible(dev->of_node, "qcom,pcie-ipq8064"))
>>> +		res->phy_tx0_term_offset = 7;
>>
>> Before your change the phy_tx0_term_offser was 0 for apq8064, but here
>> you change it to 7, why?
>>
> 
> apq8064 board should use qcom,pcie-apq8064 right? This should be set to 0
> only with pcie-ipq8064 compatible. Tell me if I'm wrong.

Sorry, my fault. I read the compatible check above as apq8064 but it is ipq.

-- 
regards,
Stan



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux