Hi Jishnu,
It is nice to cc a reviewer from a previous version. Just saw this.
On Mon, Apr 27, 2020 at 6:55 PM Jishnu Prakash <jprakash@xxxxxxxxxxxxxx> wrote:
>
> The ADC architecture on PMIC7 is changed as compared to PMIC5. The
> major change from PMIC5 is that all SW communication to ADC goes through
> PMK8350, which communicates with other PMICs through PBS when the ADC
> on PMK8350 works in master mode. The SID register is used to identify the
> PMICs with which the PBS needs to communicate. Add support for the same.
>
> Signed-off-by: Jishnu Prakash <jprakash@xxxxxxxxxxxxxx>
> ---
> drivers/iio/adc/qcom-spmi-adc5.c | 239 +++++++++++++++++++++++++++++++++-
> drivers/iio/adc/qcom-vadc-common.c | 260 +++++++++++++++++++++++++++++++++++++
> drivers/iio/adc/qcom-vadc-common.h | 15 +++
> 3 files changed, 510 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/iio/adc/qcom-spmi-adc5.c b/drivers/iio/adc/qcom-spmi-adc5.c
> index 21fdcde..a66eeb7 100644
> --- a/drivers/iio/adc/qcom-spmi-adc5.c
> +++ b/drivers/iio/adc/qcom-spmi-adc5.c
> @@ -1,6 +1,6 @@
> // SPDX-License-Identifier: GPL-2.0
> /*
> - * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2018, 2020, The Linux Foundation. All rights reserved.
> */
>
> #include <linux/bitops.h>
> @@ -23,6 +23,7 @@
>
> #define ADC5_USR_REVISION1 0x0
> #define ADC5_USR_STATUS1 0x8
> +#define ADC5_USR_STATUS1_CONV_FAULT BIT(7)
> #define ADC5_USR_STATUS1_REQ_STS BIT(1)
> #define ADC5_USR_STATUS1_EOC BIT(0)
> #define ADC5_USR_STATUS1_REQ_STS_EOC_MASK 0x3
> @@ -65,6 +66,9 @@
>
> #define ADC5_USR_IBAT_DATA1 0x53
>
> +#define ADC_CHANNEL_OFFSET 0x8
> +#define ADC_CHANNEL_MASK GENMASK(7, 0)
> +
> /*
> * Conversion time varies based on the decimation, clock rate, fast average
> * samples and measurements queued across different VADC peripherals.
> @@ -79,6 +83,11 @@
> #define ADC5_HW_SETTLE_DIFF_MINOR 3
> #define ADC5_HW_SETTLE_DIFF_MAJOR 5
>
> +/* For PMIC7 */
> +#define ADC_APP_SID 0x40
> +#define ADC_APP_SID_MASK GENMASK(3, 0)
> +#define ADC7_CONV_TIMEOUT msecs_to_jiffies(10)
> +
> enum adc5_cal_method {
> ADC5_NO_CAL = 0,
> ADC5_RATIOMETRIC_CAL,
> @@ -96,6 +105,7 @@ enum adc5_cal_val {
> * @cal_method: calibration method.
> * @cal_val: calibration value
> * @decimation: sampling rate supported for the channel.
> + * @sid: slave id of PMIC owning the channel, for PMIC7.
> * @prescale: channel scaling performed on the input signal.
> * @hw_settle_time: the time between AMUX being configured and the
> * start of conversion.
> @@ -110,6 +120,7 @@ struct adc5_channel_prop {
> enum adc5_cal_method cal_method;
> enum adc5_cal_val cal_val;
> unsigned int decimation;
> + unsigned int sid;
> unsigned int prescale;
> unsigned int hw_settle_time;
> unsigned int avg_samples;
> @@ -140,6 +151,7 @@ struct adc5_chip {
> bool poll_eoc;
> struct completion complete;
> struct mutex lock;
> + int irq_eoc;
> const struct adc5_data *data;
> };
>
> @@ -155,6 +167,8 @@ static const struct vadc_prescale_ratio adc5_prescale_ratios[] = {
> {.num = 1, .den = 16}
> };
>
> +static const struct adc5_data adc7_data_pmic;
> +
> static int adc5_read(struct adc5_chip *adc, u16 offset, u8 *data, int len)
> {
> return regmap_bulk_read(adc->regmap, adc->base + offset, data, len);
> @@ -165,6 +179,11 @@ static int adc5_write(struct adc5_chip *adc, u16 offset, u8 *data, int len)
> return regmap_bulk_write(adc->regmap, adc->base + offset, data, len);
> }
>
> +static int adc5_masked_write(struct adc5_chip *adc, u16 offset, u8 mask, u8 val)
> +{
> + return regmap_update_bits(adc->regmap, adc->base + offset, mask, val);
> +}
> +
> static int adc5_prescaling_from_dt(u32 num, u32 den)
> {
> unsigned int pre;
> @@ -314,6 +333,47 @@ static int adc5_configure(struct adc5_chip *adc,
> return adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
> }
>
> +static int adc7_configure(struct adc5_chip *adc,
> + struct adc5_channel_prop *prop)
> +{
> + int ret;
> + u8 conv_req = 0, buf[4];
> +
> + ret = adc5_masked_write(adc, ADC_APP_SID, ADC_APP_SID_MASK, prop->sid);
> + if (ret)
> + return ret;
> +
> + ret = adc5_read(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
> + if (ret < 0)
> + return ret;
> +
> + /* Digital param selection */
> + adc5_update_dig_param(adc, prop, &buf[0]);
> +
> + /* Update fast average sample value */
> + buf[1] &= 0xff & ~ADC5_USR_FAST_AVG_CTL_SAMPLES_MASK;
Did you answer Andy's query about this in v2? I couldn't find it.
> + buf[1] |= prop->avg_samples;
> +
> + /* Select ADC channel */
> + buf[2] = prop->channel;
> +
> + /* Select HW settle delay for channel */
> + buf[3] &= 0xff & ~ADC5_USR_HW_SETTLE_DELAY_MASK;
Same here.
> + buf[3] |= prop->hw_settle_time;
> +
> + /* Select CONV request */
> + conv_req = ADC5_USR_CONV_REQ_REQ;
> +
> + if (!adc->poll_eoc)
> + reinit_completion(&adc->complete);
> +
> + ret = adc5_write(adc, ADC5_USR_DIG_PARAM, buf, sizeof(buf));
> + if (ret)
> + return ret;
> +
> + return adc5_write(adc, ADC5_USR_CONV_REQ, &conv_req, 1);
Is it required to call adc5_write() twice here in sequence on the
adc7? adc5_configure() above manages just fine by having an extra
element in buf and one call.
> +}
> +
> static int adc5_do_conversion(struct adc5_chip *adc,
> struct adc5_channel_prop *prop,
> struct iio_chan_spec const *chan,
> @@ -355,6 +415,43 @@ static int adc5_do_conversion(struct adc5_chip *adc,
> return ret;
> }
>
> +static int adc7_do_conversion(struct adc5_chip *adc,
> + struct adc5_channel_prop *prop,
> + struct iio_chan_spec const *chan,
> + u16 *data_volt, u16 *data_cur)
> +{
> + int ret;
> + u8 status;
> +
> + mutex_lock(&adc->lock);
> +
> + ret = adc7_configure(adc, prop);
> + if (ret) {
> + dev_err(adc->dev, "ADC configure failed with %d\n", ret);
> + goto unlock;
> + }
> +
> + /* No support for polling mode at present */
> + wait_for_completion_timeout(&adc->complete, ADC7_CONV_TIMEOUT);
> +
> + ret = adc5_read(adc, ADC5_USR_STATUS1, &status, 1);
> + if (ret < 0)
> + goto unlock;
> +
> + if (status & ADC5_USR_STATUS1_CONV_FAULT) {
> + dev_err(adc->dev, "Unexpected conversion fault\n");
> + ret = -EIO;
> + goto unlock;
> + }
> +
> + ret = adc5_read_voltage_data(adc, data_volt);
> +
> +unlock:
> + mutex_unlock(&adc->lock);
> +
> + return ret;
> +}
> +
> static irqreturn_t adc5_isr(int irq, void *dev_id)
> {
> struct adc5_chip *adc = dev_id;
> @@ -377,6 +474,56 @@ static int adc5_of_xlate(struct iio_dev *indio_dev,
> return -EINVAL;
> }
>
> +static int adc7_of_xlate(struct iio_dev *indio_dev,
> + const struct of_phandle_args *iiospec)
> +{
> + struct adc5_chip *adc = iio_priv(indio_dev);
> + int i, v_channel;
> +
> + for (i = 0; i < adc->nchannels; i++) {
> + v_channel = (adc->chan_props[i].sid << ADC_CHANNEL_OFFSET |
> + adc->chan_props[i].channel);
> + if (v_channel == iiospec->args[0])
> + return i;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int adc7_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val, int *val2,
> + long mask)
Just a nit. Since all your adc7 functions follow your adc5 functions,
please move this below adc5_read_raw for consistency.
> +{
> + struct adc5_chip *adc = iio_priv(indio_dev);
> + struct adc5_channel_prop *prop;
> + u16 adc_code_volt, adc_code_cur;
> + int ret;
> +
> + prop = &adc->chan_props[chan->address];
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_PROCESSED:
> + ret = adc7_do_conversion(adc, prop, chan,
Except for this bit (call to adc7_do_conversion instead of
adc5_do_conversion), this function is identical to adc5_read_raw.
How about making adc5_read_raw and adc7_read_raw a shim around a
function adc_read_raw_common() that takes a function pointer?
> + &adc_code_volt, &adc_code_cur);
> + if (ret)
> + return ret;
> +
> + ret = qcom_adc5_hw_scale(prop->scale_fn_type,
> + &adc5_prescale_ratios[prop->prescale],
> + adc->data,
> + adc_code_volt, val);
> +
> + if (ret)
> + return ret;
> +
> + return IIO_VAL_INT;
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> static int adc5_read_raw(struct iio_dev *indio_dev,
> struct iio_chan_spec const *chan, int *val, int *val2,
> long mask)
> @@ -415,6 +562,11 @@ static const struct iio_info adc5_info = {
> .of_xlate = adc5_of_xlate,
> };
>
> +static const struct iio_info adc7_info = {
> + .read_raw = adc7_read_raw,
> + .of_xlate = adc7_of_xlate,
> +};
> +
> struct adc5_channels {
> const char *datasheet_name;
> unsigned int prescale_index;
> @@ -477,6 +629,39 @@ static const struct adc5_channels adc5_chans_pmic[ADC5_MAX_CHANNEL] = {
> SCALE_HW_CALIB_PM5_SMB_TEMP)
> };
>
> +static const struct adc5_channels adc7_chans_pmic[ADC5_MAX_CHANNEL] = {
> + [ADC7_REF_GND] = ADC5_CHAN_VOLT("ref_gnd", 0,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC7_1P25VREF] = ADC5_CHAN_VOLT("vref_1p25", 0,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC7_VPH_PWR] = ADC5_CHAN_VOLT("vph_pwr", 1,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC7_VBAT_SNS] = ADC5_CHAN_VOLT("vbat_sns", 3,
> + SCALE_HW_CALIB_DEFAULT)
> + [ADC7_DIE_TEMP] = ADC5_CHAN_TEMP("die_temp", 0,
> + SCALE_HW_CALIB_PMIC_THERM_PM7)
> + [ADC7_AMUX_THM1_100K_PU] = ADC5_CHAN_TEMP("amux_thm1_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_AMUX_THM2_100K_PU] = ADC5_CHAN_TEMP("amux_thm2_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_AMUX_THM3_100K_PU] = ADC5_CHAN_TEMP("amux_thm3_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_AMUX_THM4_100K_PU] = ADC5_CHAN_TEMP("amux_thm4_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_AMUX_THM5_100K_PU] = ADC5_CHAN_TEMP("amux_thm5_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_AMUX_THM6_100K_PU] = ADC5_CHAN_TEMP("amux_thm6_pu2", 0,
Use space instead of tab for indentation in all the THMx channels to
make it look more in line.
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_GPIO1_100K_PU] = ADC5_CHAN_TEMP("gpio1_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_GPIO2_100K_PU] = ADC5_CHAN_TEMP("gpio2_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_GPIO3_100K_PU] = ADC5_CHAN_TEMP("gpio3_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> + [ADC7_GPIO4_100K_PU] = ADC5_CHAN_TEMP("gpio4_pu2", 0,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7)
> +};
> +
> static const struct adc5_channels adc5_chans_rev2[ADC5_MAX_CHANNEL] = {
> [ADC5_REF_GND] = ADC5_CHAN_VOLT("ref_gnd", 0,
> SCALE_HW_CALIB_DEFAULT)
> @@ -511,6 +696,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
> {
> const char *name = node->name, *channel_name;
> u32 chan, value, varr[2];
> + u32 sid = 0;
> int ret;
> struct device *dev = adc->dev;
>
> @@ -520,6 +706,15 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
> return ret;
> }
>
> + /* Value read from "reg" is virtual channel number */
> +
> + /* virtual channel number = sid << 8 | channel number */
> +
> + if (adc->data == &adc7_data_pmic) {
> + sid = chan >> ADC_CHANNEL_OFFSET;
> + chan = chan & ADC_CHANNEL_MASK;
> + }
> +
> if (chan > ADC5_PARALLEL_ISENSE_VBAT_IDATA ||
> !data->adc_chans[chan].datasheet_name) {
> dev_err(dev, "%s invalid channel number %d\n", name, chan);
> @@ -528,6 +723,7 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
>
> /* the channel has DT description */
> prop->channel = chan;
> + prop->sid = sid;
>
> channel_name = of_get_property(node,
> "label", NULL) ? : node->name;
> @@ -578,8 +774,9 @@ static int adc5_get_dt_channel_data(struct adc5_chip *adc,
> pr_debug("dig_ver:minor:%d, major:%d\n", dig_version[0],
> dig_version[1]);
> /* Digital controller >= 5.3 have hw_settle_2 option */
> - if (dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
> - dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR)
> + if ((dig_version[0] >= ADC5_HW_SETTLE_DIFF_MINOR &&
> + dig_version[1] >= ADC5_HW_SETTLE_DIFF_MAJOR) ||
> + adc->data == &adc7_data_pmic)
> ret = adc5_hw_settle_time_from_dt(value,
> data->hw_settle_2);
> else
> @@ -629,6 +826,7 @@ static const struct adc5_data adc5_data_pmic = {
> .full_scale_code_volt = 0x70e4,
> .full_scale_code_cur = 0x2710,
> .adc_chans = adc5_chans_pmic,
> + .info = &adc5_info,
This belongs in a separate patch along with the change in
adc5_data_pmic_rev2 below
> .decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
> {250, 420, 840},
> .hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
> @@ -639,10 +837,23 @@ static const struct adc5_data adc5_data_pmic = {
> 1, 2, 4, 8, 16, 32, 64, 128},
> };
>
> +static const struct adc5_data adc7_data_pmic = {
> + .full_scale_code_volt = 0x70e4,
> + .adc_chans = adc7_chans_pmic,
> + .info = &adc7_info,
> + .decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
> + {85, 340, 1360},
> + .hw_settle_2 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
> + {15, 100, 200, 300, 400, 500, 600, 700,
> + 1000, 2000, 4000, 8000, 16000, 32000,
> + 64000, 128000},
> +};
> +
> static const struct adc5_data adc5_data_pmic_rev2 = {
> .full_scale_code_volt = 0x4000,
> .full_scale_code_cur = 0x1800,
> .adc_chans = adc5_chans_rev2,
> + .info = &adc5_info,
Separate patch.
> .decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
> {256, 512, 1024},
> .hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
> @@ -659,6 +870,10 @@ static const struct of_device_id adc5_match_table[] = {
> .data = &adc5_data_pmic,
> },
> {
> + .compatible = "qcom,spmi-adc7",
> + .data = &adc7_data_pmic,
> + },
> + {
> .compatible = "qcom,spmi-adc-rev2",
> .data = &adc5_data_pmic_rev2,
> },
> @@ -752,6 +967,9 @@ static int adc5_probe(struct platform_device *pdev)
> adc->regmap = regmap;
> adc->dev = dev;
> adc->base = reg;
> +
> + platform_set_drvdata(pdev, adc);
> +
> init_completion(&adc->complete);
> mutex_init(&adc->lock);
>
> @@ -761,6 +979,8 @@ static int adc5_probe(struct platform_device *pdev)
> return ret;
> }
>
> + indio_dev->info = adc->data->info;
> +
> irq_eoc = platform_get_irq(pdev, 0);
> if (irq_eoc < 0) {
> if (irq_eoc == -EPROBE_DEFER || irq_eoc == -EINVAL)
> @@ -773,23 +993,34 @@ static int adc5_probe(struct platform_device *pdev)
> return ret;
> }
>
> + adc->irq_eoc = irq_eoc;
> +
I think this belongs in a separate patch along with the adc5_exit
function below.
> indio_dev->dev.parent = dev;
> indio_dev->dev.of_node = node;
> indio_dev->name = pdev->name;
> indio_dev->modes = INDIO_DIRECT_MODE;
> - indio_dev->info = &adc5_info;
> indio_dev->channels = adc->iio_chans;
> indio_dev->num_channels = adc->nchannels;
>
> return devm_iio_device_register(dev, indio_dev);
> }
>
> +static int adc5_exit(struct platform_device *pdev)
> +{
> + struct adc5_chip *adc = platform_get_drvdata(pdev);
> +
> + if (adc->irq_eoc >= 0)
> + disable_irq(adc->irq_eoc);
> + return 0;
> +}
> +
> static struct platform_driver adc5_driver = {
> .driver = {
> .name = "qcom-spmi-adc5.c",
> .of_match_table = adc5_match_table,
> },
> .probe = adc5_probe,
> + .remove = adc5_exit,
This really belongs in a separate patch
> };
> module_platform_driver(adc5_driver);
>
> diff --git a/drivers/iio/adc/qcom-vadc-common.c b/drivers/iio/adc/qcom-vadc-common.c
> index 2bb78d1..b6915c2 100644
> --- a/drivers/iio/adc/qcom-vadc-common.c
> +++ b/drivers/iio/adc/qcom-vadc-common.c
> @@ -89,6 +89,195 @@ static const struct vadc_map_pt adcmap_100k_104ef_104fb_1875_vref[] = {
> { 46, 125000 },
> };
>
> +static const struct vadc_map_pt adcmap7_die_temp[] = {
> + { 433700, 1967},
> + { 473100, 1964},
> + { 512400, 1957},
> + { 551500, 1949},
> + { 590500, 1940},
> + { 629300, 1930},
> + { 667900, 1921},
> + { 706400, 1910},
> + { 744600, 1896},
> + { 782500, 1878},
> + { 820100, 1859},
> + { 857300, 0},
> +};
> +
> +/*
> + * Resistance to temperature table for 100k pull up for NTCG104EF104.
> + */
> +static const struct vadc_map_pt adcmap7_100k[] = {
> + { 4250657, -40960 },
> + { 3962085, -39936 },
> + { 3694875, -38912 },
> + { 3447322, -37888 },
> + { 3217867, -36864 },
> + { 3005082, -35840 },
> + { 2807660, -34816 },
> + { 2624405, -33792 },
> + { 2454218, -32768 },
> + { 2296094, -31744 },
> + { 2149108, -30720 },
> + { 2012414, -29696 },
> + { 1885232, -28672 },
> + { 1766846, -27648 },
> + { 1656598, -26624 },
> + { 1553884, -25600 },
> + { 1458147, -24576 },
> + { 1368873, -23552 },
> + { 1285590, -22528 },
> + { 1207863, -21504 },
> + { 1135290, -20480 },
> + { 1067501, -19456 },
> + { 1004155, -18432 },
> + { 944935, -17408 },
> + { 889550, -16384 },
> + { 837731, -15360 },
> + { 789229, -14336 },
> + { 743813, -13312 },
> + { 701271, -12288 },
> + { 661405, -11264 },
> + { 624032, -10240 },
> + { 588982, -9216 },
> + { 556100, -8192 },
> + { 525239, -7168 },
> + { 496264, -6144 },
> + { 469050, -5120 },
> + { 443480, -4096 },
> + { 419448, -3072 },
> + { 396851, -2048 },
> + { 375597, -1024 },
> + { 355598, 0 },
> + { 336775, 1024 },
> + { 319052, 2048 },
> + { 302359, 3072 },
> + { 286630, 4096 },
> + { 271806, 5120 },
> + { 257829, 6144 },
> + { 244646, 7168 },
> + { 232209, 8192 },
> + { 220471, 9216 },
> + { 209390, 10240 },
> + { 198926, 11264 },
> + { 189040, 12288 },
> + { 179698, 13312 },
> + { 170868, 14336 },
> + { 162519, 15360 },
> + { 154622, 16384 },
> + { 147150, 17408 },
> + { 140079, 18432 },
> + { 133385, 19456 },
> + { 127046, 20480 },
> + { 121042, 21504 },
> + { 115352, 22528 },
> + { 109960, 23552 },
> + { 104848, 24576 },
> + { 100000, 25600 },
> + { 95402, 26624 },
> + { 91038, 27648 },
> + { 86897, 28672 },
> + { 82965, 29696 },
> + { 79232, 30720 },
> + { 75686, 31744 },
> + { 72316, 32768 },
> + { 69114, 33792 },
> + { 66070, 34816 },
> + { 63176, 35840 },
> + { 60423, 36864 },
> + { 57804, 37888 },
> + { 55312, 38912 },
> + { 52940, 39936 },
> + { 50681, 40960 },
> + { 48531, 41984 },
> + { 46482, 43008 },
> + { 44530, 44032 },
> + { 42670, 45056 },
> + { 40897, 46080 },
> + { 39207, 47104 },
> + { 37595, 48128 },
> + { 36057, 49152 },
> + { 34590, 50176 },
> + { 33190, 51200 },
> + { 31853, 52224 },
> + { 30577, 53248 },
> + { 29358, 54272 },
> + { 28194, 55296 },
> + { 27082, 56320 },
> + { 26020, 57344 },
> + { 25004, 58368 },
> + { 24033, 59392 },
> + { 23104, 60416 },
> + { 22216, 61440 },
> + { 21367, 62464 },
> + { 20554, 63488 },
> + { 19776, 64512 },
> + { 19031, 65536 },
> + { 18318, 66560 },
> + { 17636, 67584 },
> + { 16982, 68608 },
> + { 16355, 69632 },
> + { 15755, 70656 },
> + { 15180, 71680 },
> + { 14628, 72704 },
> + { 14099, 73728 },
> + { 13592, 74752 },
> + { 13106, 75776 },
> + { 12640, 76800 },
> + { 12192, 77824 },
> + { 11762, 78848 },
> + { 11350, 79872 },
> + { 10954, 80896 },
> + { 10574, 81920 },
> + { 10209, 82944 },
> + { 9858, 83968 },
> + { 9521, 84992 },
> + { 9197, 86016 },
> + { 8886, 87040 },
> + { 8587, 88064 },
> + { 8299, 89088 },
> + { 8023, 90112 },
> + { 7757, 91136 },
> + { 7501, 92160 },
> + { 7254, 93184 },
> + { 7017, 94208 },
> + { 6789, 95232 },
> + { 6570, 96256 },
> + { 6358, 97280 },
> + { 6155, 98304 },
> + { 5959, 99328 },
> + { 5770, 100352 },
> + { 5588, 101376 },
> + { 5412, 102400 },
> + { 5243, 103424 },
> + { 5080, 104448 },
> + { 4923, 105472 },
> + { 4771, 106496 },
> + { 4625, 107520 },
> + { 4484, 108544 },
> + { 4348, 109568 },
> + { 4217, 110592 },
> + { 4090, 111616 },
> + { 3968, 112640 },
> + { 3850, 113664 },
> + { 3736, 114688 },
> + { 3626, 115712 },
> + { 3519, 116736 },
> + { 3417, 117760 },
> + { 3317, 118784 },
> + { 3221, 119808 },
> + { 3129, 120832 },
> + { 3039, 121856 },
> + { 2952, 122880 },
> + { 2868, 123904 },
> + { 2787, 124928 },
> + { 2709, 125952 },
> + { 2633, 126976 },
> + { 2560, 128000 },
> + { 2489, 129024 },
> + { 2420, 130048 }
> +};
> +
> static int qcom_vadc_scale_hw_calib_volt(
> const struct vadc_prescale_ratio *prescale,
> const struct adc5_data *data,
> @@ -97,6 +286,10 @@ static int qcom_vadc_scale_hw_calib_therm(
> const struct vadc_prescale_ratio *prescale,
> const struct adc5_data *data,
> u16 adc_code, int *result_mdec);
> +static int qcom_vadc7_scale_hw_calib_therm(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc5_data *data,
> + u16 adc_code, int *result_mdec);
> static int qcom_vadc_scale_hw_smb_temp(
> const struct vadc_prescale_ratio *prescale,
> const struct adc5_data *data,
> @@ -109,12 +302,20 @@ static int qcom_vadc_scale_hw_calib_die_temp(
> const struct vadc_prescale_ratio *prescale,
> const struct adc5_data *data,
> u16 adc_code, int *result_mdec);
> +static int qcom_vadc7_scale_hw_calib_die_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc5_data *data,
> + u16 adc_code, int *result_mdec);
>
> static struct qcom_adc5_scale_type scale_adc5_fn[] = {
> [SCALE_HW_CALIB_DEFAULT] = {qcom_vadc_scale_hw_calib_volt},
> [SCALE_HW_CALIB_THERM_100K_PULLUP] = {qcom_vadc_scale_hw_calib_therm},
> [SCALE_HW_CALIB_XOTHERM] = {qcom_vadc_scale_hw_calib_therm},
> + [SCALE_HW_CALIB_THERM_100K_PU_PM7] = {
> + qcom_vadc7_scale_hw_calib_therm},
> [SCALE_HW_CALIB_PMIC_THERM] = {qcom_vadc_scale_hw_calib_die_temp},
> + [SCALE_HW_CALIB_PMIC_THERM_PM7] = {
> + qcom_vadc7_scale_hw_calib_die_temp},
> [SCALE_HW_CALIB_PM5_CHG_TEMP] = {qcom_vadc_scale_hw_chg5_temp},
> [SCALE_HW_CALIB_PM5_SMB_TEMP] = {qcom_vadc_scale_hw_smb_temp},
> };
> @@ -291,6 +492,32 @@ static int qcom_vadc_scale_code_voltage_factor(u16 adc_code,
> return (int) voltage;
> }
>
> +static int qcom_vadc7_scale_hw_calib_therm(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc5_data *data,
> + u16 adc_code, int *result_mdec)
> +{
> + s64 resistance = adc_code;
> + int ret, result;
> +
> + if (adc_code >= RATIO_MAX_ADC7)
> + return -EINVAL;
> +
> + /* (ADC code * R_PULLUP (100Kohm)) / (full_scale_code - ADC code)*/
> + resistance *= R_PU_100K;
> + resistance = div64_s64(resistance, RATIO_MAX_ADC7 - adc_code);
> +
> + ret = qcom_vadc_map_voltage_temp(adcmap7_100k,
> + ARRAY_SIZE(adcmap7_100k),
> + resistance, &result);
> + if (ret)
> + return ret;
> +
> + *result_mdec = result;
> +
> + return 0;
> +}
> +
> static int qcom_vadc_scale_hw_calib_volt(
> const struct vadc_prescale_ratio *prescale,
> const struct adc5_data *data,
> @@ -330,6 +557,39 @@ static int qcom_vadc_scale_hw_calib_die_temp(
> return 0;
> }
>
> +static int qcom_vadc7_scale_hw_calib_die_temp(
> + const struct vadc_prescale_ratio *prescale,
> + const struct adc5_data *data,
> + u16 adc_code, int *result_mdec)
> +{
> +
> + int voltage, vtemp0, temp, i = ARRAY_SIZE(adcmap7_die_temp) - 1;
> +
> + voltage = qcom_vadc_scale_code_voltage_factor(adc_code,
> + prescale, data, 1);
> +
> + if (adcmap7_die_temp[0].x > voltage) {
> + *result_mdec = DIE_TEMP_ADC7_SCALE_1;
> + return 0;
> + } else if (adcmap7_die_temp[i].x <= voltage) {
> + *result_mdec = DIE_TEMP_ADC7_MAX;
> + return 0;
> + }
> +
> + for (i = 0; i < ARRAY_SIZE(adcmap7_die_temp); i++)
> + if (adcmap7_die_temp[i].x > voltage)
> + break;
> +
> + vtemp0 = adcmap7_die_temp[i - 1].x;
> + voltage = voltage - vtemp0;
> + temp = div64_s64(voltage * DIE_TEMP_ADC7_SCALE_FACTOR,
> + adcmap7_die_temp[i - 1].y);
> + temp += DIE_TEMP_ADC7_SCALE_1 + (DIE_TEMP_ADC7_SCALE_2 * (i - 1));
> + *result_mdec = temp;
> +
> + return 0;
> +}
> +
> static int qcom_vadc_scale_hw_smb_temp(
> const struct vadc_prescale_ratio *prescale,
> const struct adc5_data *data,
> diff --git a/drivers/iio/adc/qcom-vadc-common.h b/drivers/iio/adc/qcom-vadc-common.h
> index e074902a..d195e83 100644
> --- a/drivers/iio/adc/qcom-vadc-common.h
> +++ b/drivers/iio/adc/qcom-vadc-common.h
> @@ -49,6 +49,14 @@
> #define ADC5_FULL_SCALE_CODE 0x70e4
> #define ADC5_USR_DATA_CHECK 0x8000
>
> +#define R_PU_100K 100000
> +#define RATIO_MAX_ADC7 0x4000
> +
> +#define DIE_TEMP_ADC7_SCALE_1 -60000
> +#define DIE_TEMP_ADC7_SCALE_2 20000
> +#define DIE_TEMP_ADC7_SCALE_FACTOR 1000
> +#define DIE_TEMP_ADC7_MAX 160000
> +
> /**
> * struct vadc_map_pt - Map the graph representation for ADC channel
> * @x: Represent the ADC digitized code.
> @@ -110,8 +118,12 @@ struct vadc_prescale_ratio {
> * lookup table. The hardware applies offset/slope to adc code.
> * SCALE_HW_CALIB_XOTHERM: Returns XO thermistor voltage in millidegC using
> * 100k pullup. The hardware applies offset/slope to adc code.
> + * SCALE_HW_CALIB_THERM_100K_PU_PM7: Returns temperature in millidegC using
> + * lookup table for PMIC7. The hardware applies offset/slope to adc code.
> * SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
> * The hardware applies offset/slope to adc code.
> + * SCALE_HW_CALIB_PMIC_THERM: Returns result in milli degree's Centigrade.
> + * The hardware applies offset/slope to adc code. This is for PMIC7.
> * SCALE_HW_CALIB_PM5_CHG_TEMP: Returns result in millidegrees for PMIC5
> * charger temperature.
> * SCALE_HW_CALIB_PM5_SMB_TEMP: Returns result in millidegrees for PMIC5
> @@ -126,7 +138,9 @@ enum vadc_scale_fn_type {
> SCALE_HW_CALIB_DEFAULT,
> SCALE_HW_CALIB_THERM_100K_PULLUP,
> SCALE_HW_CALIB_XOTHERM,
> + SCALE_HW_CALIB_THERM_100K_PU_PM7,
> SCALE_HW_CALIB_PMIC_THERM,
> + SCALE_HW_CALIB_PMIC_THERM_PM7,
> SCALE_HW_CALIB_PM5_CHG_TEMP,
> SCALE_HW_CALIB_PM5_SMB_TEMP,
> SCALE_HW_CALIB_INVALID,
> @@ -136,6 +150,7 @@ struct adc5_data {
> const u32 full_scale_code_volt;
> const u32 full_scale_code_cur;
> const struct adc5_channels *adc_chans;
> + const struct iio_info *info;
> unsigned int *decimation;
> unsigned int *hw_settle_1;
> unsigned int *hw_settle_2;
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
