[PATCH] arm64: dts: ipq8074: Re-arrange dts nodes based on address

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This patch re-arranges ipq8074 device nodes based on node address
followed by node names followed by node labels.

Suggested-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
Signed-off-by: Sivaprakash Murugesan <sivaprak@xxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 112 ++++---
 arch/arm64/boot/dts/qcom/ipq8074.dtsi     | 474 +++++++++++++++---------------
 2 files changed, 292 insertions(+), 294 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
index 70be3f9..6754cb0 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -24,63 +24,61 @@
 		device_type = "memory";
 		reg = <0x0 0x40000000 0x0 0x20000000>;
 	};
+};
+
+&blsp1_i2c2 {
+	status = "ok";
+};
+
+&blsp1_spi1 {
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&blsp1_uart3 {
+	status = "ok";
+};
+
+&blsp1_uart5 {
+	status = "ok";
+};
+
+&pcie0 {
+	status = "ok";
+	perst-gpio = <&tlmm 61 0x1>;
+};
+
+&pcie1 {
+	status = "ok";
+	perst-gpio = <&tlmm 58 0x1>;
+};
+
+&pcie_phy0 {
+	status = "ok";
+};
+
+&pcie_phy1 {
+	status = "ok";
+};
+
+&qpic_bam {
+	status = "ok";
+};
+
+&qpic_nand {
+	status = "ok";
 
-	soc {
-		serial@78b3000 {
-			status = "ok";
-		};
-
-		spi@78b5000 {
-			status = "ok";
-
-			m25p80@0 {
-				  #address-cells = <1>;
-				  #size-cells = <1>;
-				  compatible = "jedec,spi-nor";
-				  reg = <0>;
-				  spi-max-frequency = <50000000>;
-			};
-		};
-
-		serial@78b1000 {
-			 status = "ok";
-		};
-
-		i2c@78b6000 {
-			 status = "ok";
-		};
-
-		dma@7984000 {
-			 status = "ok";
-		};
-
-		nand@79b0000 {
-			status = "ok";
-
-			nand@0 {
-				reg = <0>;
-				nand-ecc-strength = <4>;
-				nand-ecc-step-size = <512>;
-				nand-bus-width = <8>;
-			};
-		};
-
-		phy@86000 {
-			status = "ok";
-		};
-
-		phy@8e000 {
-			status = "ok";
-		};
-
-		pci@20000000 {
-			status = "ok";
-			perst-gpio = <&tlmm 58 0x1>;
-		};
-
-		pci@10000000 {
-			status = "ok";
-			perst-gpio = <&tlmm 61 0x1>;
-		};
+	nand@0 {
+		reg = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 2b31823..5303821 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -10,15 +10,111 @@
 	model = "Qualcomm Technologies, Inc. IPQ8074";
 	compatible = "qcom,ipq8074";
 
+	clocks {
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+
+		xo: xo {
+			compatible = "fixed-clock";
+			clock-frequency = <19200000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <0x2>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
 	soc: soc {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		ranges = <0 0 0 0xffffffff>;
 		compatible = "simple-bus";
 
+		pcie_phy0: phy@86000 {
+			compatible = "qcom,ipq8074-qmp-pcie-phy";
+			reg = <0x00086000 0x1000>;
+			#phy-cells = <0>;
+			clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+			clock-names = "pipe_clk";
+			clock-output-names = "pcie20_phy0_pipe_clk";
+
+			resets = <&gcc GCC_PCIE0_PHY_BCR>,
+				<&gcc GCC_PCIE0PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "common";
+			status = "disabled";
+		};
+
+		pcie_phy1: phy@8e000 {
+			compatible = "qcom,ipq8074-qmp-pcie-phy";
+			reg = <0x0008e000 0x1000>;
+			#phy-cells = <0>;
+			clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
+			clock-names = "pipe_clk";
+			clock-output-names = "pcie20_phy1_pipe_clk";
+
+			resets = <&gcc GCC_PCIE1_PHY_BCR>,
+				<&gcc GCC_PCIE1PHY_PHY_BCR>;
+			reset-names = "phy",
+				      "common";
+			status = "disabled";
+		};
+
 		tlmm: pinctrl@1000000 {
 			compatible = "qcom,ipq8074-pinctrl";
-			reg = <0x1000000 0x300000>;
+			reg = <0x01000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			gpio-ranges = <&tlmm 0 0 70>;
@@ -66,102 +162,16 @@
 			};
 		};
 
-		intc: interrupt-controller@b000000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			#interrupt-cells = <0x3>;
-			reg = <0xb000000 0x1000>, <0xb002000 0x1000>;
-		};
-
-		timer {
-			compatible = "arm,armv8-timer";
-			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
-		};
-
-		timer@b120000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			compatible = "arm,armv7-timer-mem";
-			reg = <0xb120000 0x1000>;
-			clock-frequency = <19200000>;
-
-			frame@b120000 {
-				frame-number = <0>;
-				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb121000 0x1000>,
-				      <0xb122000 0x1000>;
-			};
-
-			frame@b123000 {
-				frame-number = <1>;
-				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb123000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b124000 {
-				frame-number = <2>;
-				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb124000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b125000 {
-				frame-number = <3>;
-				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb125000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b126000 {
-				frame-number = <4>;
-				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb126000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b127000 {
-				frame-number = <5>;
-				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb127000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@b128000 {
-				frame-number = <6>;
-				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xb128000 0x1000>;
-				status = "disabled";
-			};
-		};
-
 		gcc: gcc@1800000 {
 			compatible = "qcom,gcc-ipq8074";
-			reg = <0x1800000 0x80000>;
+			reg = <0x01800000 0x80000>;
 			#clock-cells = <0x1>;
 			#reset-cells = <0x1>;
 		};
 
-		blsp1_uart5: serial@78b3000 {
-			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0x78b3000 0x200>;
-			interrupts = <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
-				 <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			pinctrl-0 = <&serial_4_pins>;
-			pinctrl-names = "default";
-			status = "disabled";
-		};
-
 		blsp_dma: dma@7884000 {
 			compatible = "qcom,bam-v1.7.0";
-			reg = <0x7884000 0x2b000>;
+			reg = <0x07884000 0x2b000>;
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "bam_clk";
@@ -171,7 +181,7 @@
 
 		blsp1_uart1: serial@78af000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0x78af000 0x200>;
+			reg = <0x078af000 0x200>;
 			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
@@ -181,7 +191,7 @@
 
 		blsp1_uart3: serial@78b1000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0x78b1000 0x200>;
+			reg = <0x078b1000 0x200>;
 			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
 				<&gcc GCC_BLSP1_AHB_CLK>;
@@ -194,11 +204,23 @@
 			status = "disabled";
 		};
 
+		blsp1_uart5: serial@78b3000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b3000 0x200>;
+			interrupts = <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-0 = <&serial_4_pins>;
+			pinctrl-names = "default";
+			status = "disabled";
+		};
+
 		blsp1_spi1: spi@78b5000 {
 			compatible = "qcom,spi-qup-v2.2.1";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			reg = <0x78b5000 0x600>;
+			reg = <0x078b5000 0x600>;
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 			spi-max-frequency = <50000000>;
 			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
@@ -215,7 +237,7 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			reg = <0x78b6000 0x600>;
+			reg = <0x078b6000 0x600>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
 				<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
@@ -232,7 +254,7 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			reg = <0x78b7000 0x600>;
+			reg = <0x078b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
 				<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
@@ -245,7 +267,7 @@
 
 		qpic_bam: dma@7984000 {
 			compatible = "qcom,bam-v1.7.0";
-			reg = <0x7984000 0x1a000>;
+			reg = <0x07984000 0x1a000>;
 			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_QPIC_AHB_CLK>;
 			clock-names = "bam_clk";
@@ -256,7 +278,7 @@
 
 		qpic_nand: nand@79b0000 {
 			compatible = "qcom,ipq8074-nand";
-			reg = <0x79b0000 0x10000>;
+			reg = <0x079b0000 0x10000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&gcc GCC_QPIC_CLK>,
@@ -272,104 +294,85 @@
 			status = "disabled";
 		};
 
-		pcie_phy0: phy@86000 {
-			compatible = "qcom,ipq8074-qmp-pcie-phy";
-			reg = <0x86000 0x1000>;
-			#phy-cells = <0>;
-			clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
-			clock-names = "pipe_clk";
-			clock-output-names = "pcie20_phy0_pipe_clk";
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <0x3>;
+			reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>;
+		};
 
-			resets = <&gcc GCC_PCIE0_PHY_BCR>,
-				<&gcc GCC_PCIE0PHY_PHY_BCR>;
-			reset-names = "phy",
-				      "common";
-			status = "disabled";
+		timer {
+			compatible = "arm,armv8-timer";
+			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 		};
 
-		pcie0: pci@20000000 {
-			compatible = "qcom,pcie-ipq8074";
-			reg =  <0x20000000 0xf1d
-				0x20000f20 0xa8
-				0x80000 0x2000
-				0x20100000 0x1000>;
-			reg-names = "dbi", "elbi", "parf", "config";
-			device_type = "pci";
-			linux,pci-domain = <0>;
-			bus-range = <0x00 0xff>;
-			num-lanes = <1>;
-			#address-cells = <3>;
-			#size-cells = <2>;
+		timer@b120000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0b120000 0x1000>;
+			clock-frequency = <19200000>;
 
-			phys = <&pcie_phy0>;
-			phy-names = "pciephy";
+			frame@b120000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b121000 0x1000>,
+				      <0x0b122000 0x1000>;
+			};
 
-			ranges = <0x81000000 0 0x20200000 0x20200000
-				  0 0x100000   /* downstream I/O */
-				  0x82000000 0 0x20300000 0x20300000
-				  0 0xd00000>; /* non-prefetchable memory */
+			frame@b123000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b123000 0x1000>;
+				status = "disabled";
+			};
 
-			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "msi";
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 75
-					 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 78
-					 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 79
-					 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 83
-					 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			frame@b124000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b124000 0x1000>;
+				status = "disabled";
+			};
 
-			clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
-				 <&gcc GCC_PCIE0_AXI_M_CLK>,
-				 <&gcc GCC_PCIE0_AXI_S_CLK>,
-				 <&gcc GCC_PCIE0_AHB_CLK>,
-				 <&gcc GCC_PCIE0_AUX_CLK>;
+			frame@b125000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b125000 0x1000>;
+				status = "disabled";
+			};
 
-			clock-names = "iface",
-				      "axi_m",
-				      "axi_s",
-				      "ahb",
-				      "aux";
-			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
-				 <&gcc GCC_PCIE0_SLEEP_ARES>,
-				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
-				 <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
-				 <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
-				 <&gcc GCC_PCIE0_AHB_ARES>,
-				 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>;
-			reset-names = "pipe",
-				      "sleep",
-				      "sticky",
-				      "axi_m",
-				      "axi_s",
-				      "ahb",
-				      "axi_m_sticky";
-			status = "disabled";
-		};
+			frame@b126000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b126000 0x1000>;
+				status = "disabled";
+			};
 
-		pcie_phy1: phy@8e000 {
-			compatible = "qcom,ipq8074-qmp-pcie-phy";
-			reg = <0x8e000 0x1000>;
-			#phy-cells = <0>;
-			clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
-			clock-names = "pipe_clk";
-			clock-output-names = "pcie20_phy1_pipe_clk";
+			frame@b127000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b127000 0x1000>;
+				status = "disabled";
+			};
 
-			resets = <&gcc GCC_PCIE1_PHY_BCR>,
-				<&gcc GCC_PCIE1PHY_PHY_BCR>;
-			reset-names = "phy",
-				      "common";
-			status = "disabled";
+			frame@b128000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0b128000 0x1000>;
+				status = "disabled";
+			};
 		};
 
 		pcie1: pci@10000000 {
 			compatible = "qcom,pcie-ipq8074";
 			reg =  <0x10000000 0xf1d
 				0x10000f20 0xa8
-				0x88000 0x2000
+				0x00088000 0x2000
 				0x10100000 0x1000>;
 			reg-names = "dbi", "elbi", "parf", "config";
 			device_type = "pci";
@@ -426,71 +429,68 @@
 				      "axi_m_sticky";
 			status = "disabled";
 		};
-	};
-
-	cpus {
-		#address-cells = <0x1>;
-		#size-cells = <0x0>;
-
-		CPU0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a53";
-			reg = <0x0>;
-			next-level-cache = <&L2_0>;
-			enable-method = "psci";
-		};
-
-		CPU1: cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a53";
-			enable-method = "psci";
-			reg = <0x1>;
-			next-level-cache = <&L2_0>;
-		};
 
-		CPU2: cpu@2 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a53";
-			enable-method = "psci";
-			reg = <0x2>;
-			next-level-cache = <&L2_0>;
-		};
-
-		CPU3: cpu@3 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a53";
-			enable-method = "psci";
-			reg = <0x3>;
-			next-level-cache = <&L2_0>;
-		};
+		pcie0: pci@20000000 {
+			compatible = "qcom,pcie-ipq8074";
+			reg =  <0x20000000 0xf1d
+				0x20000f20 0xa8
+				0x00080000 0x2000
+				0x20100000 0x1000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
 
-		L2_0: l2-cache {
-			compatible = "cache";
-			cache-level = <0x2>;
-		};
-	};
+			phys = <&pcie_phy0>;
+			phy-names = "pciephy";
 
-	psci {
-		compatible = "arm,psci-1.0";
-		method = "smc";
-	};
+			ranges = <0x81000000 0 0x20200000 0x20200000
+				  0 0x100000   /* downstream I/O */
+				  0x82000000 0 0x20300000 0x20300000
+				  0 0xd00000>; /* non-prefetchable memory */
 
-	pmu {
-		compatible = "arm,armv8-pmuv3";
-		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
-	};
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 75
+					 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 78
+					 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 79
+					 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 83
+					 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
-	clocks {
-		sleep_clk: sleep_clk {
-			compatible = "fixed-clock";
-			clock-frequency = <32000>;
-			#clock-cells = <0>;
-		};
+			clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
+				 <&gcc GCC_PCIE0_AXI_M_CLK>,
+				 <&gcc GCC_PCIE0_AXI_S_CLK>,
+				 <&gcc GCC_PCIE0_AHB_CLK>,
+				 <&gcc GCC_PCIE0_AUX_CLK>;
 
-		xo: xo {
-			compatible = "fixed-clock";
-			clock-frequency = <19200000>;
-			#clock-cells = <0>;
+			clock-names = "iface",
+				      "axi_m",
+				      "axi_s",
+				      "ahb",
+				      "aux";
+			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+				 <&gcc GCC_PCIE0_SLEEP_ARES>,
+				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
+				 <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
+				 <&gcc GCC_PCIE0_AHB_ARES>,
+				 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>;
+			reset-names = "pipe",
+				      "sleep",
+				      "sticky",
+				      "axi_m",
+				      "axi_s",
+				      "ahb",
+				      "axi_m_sticky";
+			status = "disabled";
 		};
 	};
 };
-- 
2.7.4




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux