On Wed 11 Mar 12:15 PDT 2020, Bryan O'Donoghue wrote:
> This patch enables the primary and secondary USB controllers on the
> qcs404-evb.
>
> Primary:
> The primary USB controller has
>
> - One USB3 SS PHY using gpio-usb-conn
> - One USB2 HS PHY in device mode only and no connector driver
> associated.
>
> Secondary:
> The second DWC3 controller which has one USB Hi-Speed PHY attached to it.
>
> Cc: Andy Gross <agross@xxxxxxxxxx>
> Cc: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: Mark Rutland <mark.rutland@xxxxxxx>
> Cc: linux-arm-msm@xxxxxxxxxxxxxxx
> Cc: devicetree@xxxxxxxxxxxxxxx
> Cc: linux-kernel@xxxxxxxxxxxxxxx
> Tested-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
Hi Bryan,
I dropped the role switching for now, did some testing and applied the
series for v5.8. Let's follow up with a patch adding the role switching
once the dwc3 discussion is sorted out.
Thanks,
Bjorn
> ---
> arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 40 ++++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> index 44c7dda1e1fc..4dc3f45282fe 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> @@ -319,6 +319,46 @@ pinconf {
> };
> };
>
> +&usb2 {
> + status = "okay";
> +};
> +
> +&usb2_phy_sec {
> + vdd-supply = <&vreg_l4_1p2>;
> + vdda1p8-supply = <&vreg_l5_1p8>;
> + vdda3p3-supply = <&vreg_l12_3p3>;
> + status = "okay";
> +};
> +
> +&usb3 {
> + status = "okay";
> + dwc3@7580000 {
> + usb-role-switch;
> + usb_con: connector {
> + compatible = "gpio-usb-b-connector";
> + label = "USB-C";
> + id-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
> + vbus-supply = <&usb3_vbus_reg>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb3_id_pin>, <&usb3_vbus_pin>;
> + status = "okay";
> + };
> + };
> +};
> +
> +&usb2_phy_prim {
> + vdd-supply = <&vreg_l4_1p2>;
> + vdda1p8-supply = <&vreg_l5_1p8>;
> + vdda3p3-supply = <&vreg_l12_3p3>;
> + status = "okay";
> +};
> +
> +&usb3_phy {
> + vdd-supply = <&vreg_l3_1p05>;
> + vdda1p8-supply = <&vreg_l5_1p8>;
> + status = "okay";
> +};
> +
> &wifi {
> status = "okay";
> vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>;
> --
> 2.25.1
>
