On 2020-03-31 23:24, Rob Herring wrote:
On Mon, Mar 23, 2020 at 11:16:55PM +0530, Kiran Gunda wrote:
Convert the qcom-wled bindings from .txt to .yaml format.
Signed-off-by: Kiran Gunda <kgunda@xxxxxxxxxxxxxx>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@xxxxxxxxxxxxxx>
Acked-by: Daniel Thompson <daniel.thompson@xxxxxxxxxx>
---
.../bindings/leds/backlight/qcom-wled.txt | 154
-----------------
.../bindings/leds/backlight/qcom-wled.yaml | 184
+++++++++++++++++++++
2 files changed, 184 insertions(+), 154 deletions(-)
delete mode 100644
Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
create mode 100644
Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
diff --git
a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
new file mode 100644
index 0000000..8a388bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
@@ -0,0 +1,184 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Binding for Qualcomm Technologies, Inc. WLED driver
+
+maintainers:
+ - Lee Jones <lee.jones@xxxxxxxxxx>
Should be the h/w owner (you), not who applies patches.
will address in next post.
+
+description: |
+ WLED (White Light Emitting Diode) driver is used for controlling
display
+ backlight that is part of PMIC on Qualcomm Technologies, Inc.
reference
+ platforms. The PMIC is connected to the host processor via SPMI
bus.
+
+properties:
+ compatible :
Drop the space ^
will address in next post.
+ enum:
+ - qcom,pm8941-wled
+ - qcom,pmi8998-wled
+ - qcom,pm660l-wled
Wrong indent (1 space too many).
will address in next post.
+
+ reg:
+ maxItems: 1
+
+ default-brightness:
+ maxItems: 1
maxItems is for arrays and this is a single scalar.
+ description:
+ brightness value on boot, value from 0-4095.
0-4095 sounds like a constraint.
will address in next post.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
There should be a common definition for this.
will address in next post.
+ default: 2048
+
+ label:
+ maxItems: 1
+ description:
+ The name of the backlight device.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/string
Already has a type. Just 'label: true' is enough.
will address in next post.
+
+ qcom,cs-out:
+ description:
+ enable current sink output.
+ This property is supported only for PM8941.
+ type: boolean
+
+ qcom,cabc:
+ description:
+ enable content adaptive backlight control.
+ type: boolean
+
+ qcom,ext-gen:
+ description:
+ use externally generated modulator signal to dim.
+ This property is supported only for PM8941.
+ type: boolean
+
+ qcom,current-limit:
+ maxItems: 1
Not an array.
will address in next post.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ mA; per-string current limit; value from 0 to 25 with
25 sounds like a constraint.
will address in next post.
+ 1 mA step. This property is supported only for pm8941.
+ default: 20
+
+ qcom,current-limit-microamp:
+ maxItems: 1
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
properties with unit suffix already have a type.
will address in next post.
+ description:
+ uA; per-string current limit; value from 0 to 30000 with
+ 2500 uA step.
steps can be expressed using 'multipleOf'
will address in next post.
+ default: 25
25 can never be a multiple of 2500
will correct in next post.
+
+ qcom,current-boost-limit:
+ maxItems: 1
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ mA; boost current limit.
+ For pm8941 one of 105, 385, 525, 805, 980, 1260, 1400, 1680.
+ Default, 805 mA.
+ For pmi8998 one of 105, 280, 450, 620, 970, 1150, 1300,
+ 1500. Default 970 mA.
Constraints.
will address in next post.
+
+ qcom,switching-freq:
+ maxItems: 1
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ kHz; switching frequency; one of 600, 640, 685, 738,
+ 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200,
+ 4800, 9600.
+ Default for pm8941 1600 kHz
+ for pmi8998 800 kHz
Constraints!
will address in next post.
+
+ qcom,ovp:
+ maxItems: 1
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ V; Over-voltage protection limit; one of 27, 29, 32, 35.
Default 29V
+ This property is supported only for PM8941.
+
+ qcom,ovp-millivolt:
+ maxItems: 1
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ mV; Over-voltage protection limit;
+ For pmi8998 one of 18100, 19600, 29600, 31100.
+ Default 29600 mV.
+ If this property is not specified for PM8941, it
+ falls back to "qcom,ovp" property.
+
+ qcom,num-strings:
+ maxItems: 1
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ number of led strings attached;
+ value for PM8941 from 1 to 3. Default 2
+ For PMI8998 from 1 to 4.
+
+ interrupts:
+ maxItems: 2
items:
- description: ...
- description: ...
will address in next post.
+ description:
+ Interrupts associated with WLED. This should be
+ "short" and "ovp" interrupts. Interrupts can be
+ specified as per the encoding listed under
+ Documentation/devicetree/bindings/spmi/
+ qcom,spmi-pmic-arb.txt.
encoding is outside the scope of the binding.
will address in next post.
+
+ interrupt-names:
+ description:
+ Interrupt names associated with the interrupts.
+ Must be "short" and "ovp". The short circuit detection
+ is not supported for PM8941.
Names should be constraints.
will address in next post.
+
+ qcom,enabled-strings:
+ maxItems: 1
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ Array of the WLED strings numbered from 0 to 3. Each
+ string of leds are operated individually. Specify the
+ list of strings used by the device. Any combination of
+ led strings can be used.
+
+ qcom,external-pfet:
+ description:
+ Specify if external PFET control for short circuit
+ protection is used. This property is supported only
+ for PMI8998.
+ type: boolean
+
+ qcom,auto-string-detection:
+ description:
+ Enables auto-detection of the WLED string configuration.
+ This feature is not supported for PM8941.
+ type: boolean
+
+required:
+ - compatible
+ - reg
+ - label
+
+examples:
+ - |
+ pm8941-wled@d800 {
backlight@...
will add in next post.
+ compatible = "qcom,pm8941-wled";
+ reg = <0xd800 0x100>;
+ label = "backlight";
+
+ qcom,cs-out;
+ qcom,current-limit = <20>;
+ qcom,current-boost-limit = <805>;
+ qcom,switching-freq = <1600>;
+ qcom,ovp = <29>;
+ qcom,num-strings = <2>;
+ qcom,enabled-strings = <0 1>;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum,
a Linux Foundation Collaborative Project
