On Sun 29 Mar 05:41 PDT 2020, Bryan O'Donoghue wrote:
> During the process of debugging a processor derived from the msm8916 which
> we found the new processor was not starting one of its PLLs.
>
> After tracing the addresses and writes that downstream was doing and
> comparing to upstream it became obvious that we were writing to a different
> register location than downstream when trying to configure the PLL.
>
Good catch.
> This error is also present in upstream msm8916.
>
> As an example clk-pll.c::clk_pll_recalc_rate wants to write to
> pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is
> defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an
> example
>
For some reason we don't specify pll->post_div_width for anything but
ipq806x, so the post_div is not considered for other platforms. This
might be a bug, but in addition to updating the config_reg address
post_div_width would have to be specified for the change to affect
clk_pll_recalc_rate().
More disturbing though is the clk_pll_set_rate() implementation, which
just writes ibits to the entire config_reg. But given that we don't have
a freq_tbl for any of these plls the function will return -EINVAL
earlier.
Lastly is clk_pll_configure() which would need this, but we don't call
it from msm8916 at this point.
So while your change is correct, afaict it's a nop unless you fill out
the other fields as well.
Regards,
Bjorn
> lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf
>
> 0x01823010 GCC_BIMC_PLL_USER_CTL
> 0x01823014 GCC_BIMC_PLL_CONFIG_CTL
>
> This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.
>
> This error is likely not apparent since the bootloader will already have
> initialized these PLLs.
>
> This patch corrects the location of config_reg from PLL_CONFIG_CTL to
> PLL_USER_CTL for all relevant PLLs on msm8916.
>
> Fixes commit 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")
>
> Cc: Georgi Djakov <georgi.djakov@xxxxxxxxxx>
> Cc: Andy Gross <agross@xxxxxxxxxx>
> Cc: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> Cc: Michael Turquette <mturquette@xxxxxxxxxxxx>
> Cc: Stephen Boyd <sboyd@xxxxxxxxxx>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
> ---
> drivers/clk/qcom/gcc-msm8916.c | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/clk/qcom/gcc-msm8916.c b/drivers/clk/qcom/gcc-msm8916.c
> index 4e329a7baf2b..17e4a5a2a9fd 100644
> --- a/drivers/clk/qcom/gcc-msm8916.c
> +++ b/drivers/clk/qcom/gcc-msm8916.c
> @@ -260,7 +260,7 @@ static struct clk_pll gpll0 = {
> .l_reg = 0x21004,
> .m_reg = 0x21008,
> .n_reg = 0x2100c,
> - .config_reg = 0x21014,
> + .config_reg = 0x21010,
> .mode_reg = 0x21000,
> .status_reg = 0x2101c,
> .status_bit = 17,
> @@ -287,7 +287,7 @@ static struct clk_pll gpll1 = {
> .l_reg = 0x20004,
> .m_reg = 0x20008,
> .n_reg = 0x2000c,
> - .config_reg = 0x20014,
> + .config_reg = 0x20010,
> .mode_reg = 0x20000,
> .status_reg = 0x2001c,
> .status_bit = 17,
> @@ -314,7 +314,7 @@ static struct clk_pll gpll2 = {
> .l_reg = 0x4a004,
> .m_reg = 0x4a008,
> .n_reg = 0x4a00c,
> - .config_reg = 0x4a014,
> + .config_reg = 0x4a010,
> .mode_reg = 0x4a000,
> .status_reg = 0x4a01c,
> .status_bit = 17,
> @@ -341,7 +341,7 @@ static struct clk_pll bimc_pll = {
> .l_reg = 0x23004,
> .m_reg = 0x23008,
> .n_reg = 0x2300c,
> - .config_reg = 0x23014,
> + .config_reg = 0x23010,
> .mode_reg = 0x23000,
> .status_reg = 0x2301c,
> .status_bit = 17,
> --
> 2.25.1
>
