Re: [PATCH v2 2/3] dt-bindings: thermal: Add yaml bindings for thermal cooling-devices

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Mar 05, 2020 at 06:26:42PM +0530, Amit Kucheria wrote:
> As part of moving the thermal bindings to YAML, split it up into 3
> bindings: thermal sensors, cooling devices and thermal zones.
> 
> The property #cooling-cells is required in each device that acts as a
> cooling device - whether active or passive. So any device that can
> throttle its performance to passively reduce heat dissipation (e.g.
> cpus, gpus) and any device that can actively dissipate heat at different
> levels (e.g. fans) will contain this property.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@xxxxxxxxxx>
> ---
>  .../thermal/thermal-cooling-devices.yaml      | 114 ++++++++++++++++++
>  1 file changed, 114 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml
> 
> diff --git a/Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml b/Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml
> new file mode 100644
> index 0000000000000..4745ea4b41ae7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml
> @@ -0,0 +1,114 @@
> +# SPDX-License-Identifier: (GPL-2.0)
> +# Copyright 2020 Linaro Ltd.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/thermal/thermal-cooling-devices.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Thermal cooling device binding
> +
> +maintainers:
> +  - Amit Kucheria <amitk@xxxxxxxxxx>
> +
> +description: |
> +  Thermal management is achieved in devicetree by describing the sensor hardware
> +  and the software abstraction of cooling devices and thermal zones required to
> +  take appropriate action to mitigate thermal overload.
> +
> +  The following node types are used to completely describe a thermal management
> +  system in devicetree:
> +   - thermal-sensor: device that measures temperature, has SoC-specific bindings
> +   - cooling-device: device used to dissipate heat either passively or artively
> +   - thermal-zones: a container of the following node types used to describe all
> +     thermal data for the platform
> +
> +  This binding describes the cooling devices.
> +
> +  There are essentially two ways to provide control on power dissipation:
> +    - Passive cooling: by means of regulating device performance. A typical
> +      passive cooling mechanism is a CPU that has dynamic voltage and frequency
> +      scaling (DVFS), and uses lower frequencies as cooling states.
> +    - Active cooling: by means of activating devices in order to remove the
> +      dissipated heat, e.g. regulating fan speeds.
> +
> +  Any cooling device has a range of cooling states (i.e. different levels of
> +  heat dissipation). They also have a way to determine the state of cooling in
> +  which the device is. For example, a fan's cooling states correspond to the
> +  different fan speeds possible. Cooling states are referred to by single
> +  unsigned integers, where larger numbers mean greater heat dissipation. The
> +  precise set of cooling states associated with a device should be defined in
> +  a particular device's binding.
> +

This and patch 1 should have a 'select: true' so that this schema is 
applied to all nodes (it does nothing if #cooling-cells is not present).

> +properties:
> +  "#cooling-cells":
> +    description:
> +        Must be 2, in order to specify minimum and maximum cooling state used in
> +        the cooling-maps reference. The first cell is the minimum cooling state
> +        and the second cell is the maximum cooling state requested.
> +    const: 2
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/thermal/thermal.h>
> +
> +    // Example 1: Cpufreq cooling device on CPU0
> +    cpus {
> +            #address-cells = <2>;
> +            #size-cells = <0>;
> +
> +            CPU0: cpu@0 {
> +                    device_type = "cpu";
> +                    compatible = "qcom,kryo385";
> +                    reg = <0x0 0x0>;
> +                    enable-method = "psci";
> +                    cpu-idle-states = <&LITTLE_CPU_SLEEP_0
> +                                       &LITTLE_CPU_SLEEP_1
> +                                       &CLUSTER_SLEEP_0>;
> +                    capacity-dmips-mhz = <607>;
> +                    dynamic-power-coefficient = <100>;
> +                    qcom,freq-domain = <&cpufreq_hw 0>;
> +                    #cooling-cells = <2>;
> +                    next-level-cache = <&L2_0>;
> +                    L2_0: l2-cache {
> +                            compatible = "cache";
> +                            next-level-cache = <&L3_0>;
> +                            L3_0: l3-cache {
> +                                    compatible = "cache";
> +                            };
> +                    };
> +          };
> +
> +          /* ... */
> +
> +    };
> +
> +    /* ... */
> +
> +    thermal-zones {
> +            cpu0-thermal {
> +                    polling-delay-passive = <250>;
> +                    polling-delay = <1000>;
> +
> +                    thermal-sensors = <&tsens0 1>;
> +
> +                    trips {
> +                            cpu0_alert0: trip-point0 {
> +                                    temperature = <90000>;
> +                                    hysteresis = <2000>;
> +                                    type = "passive";
> +                            };
> +                    };
> +
> +                    cooling-maps {
> +                            map0 {
> +                                    trip = <&cpu0_alert0>;
> +                                    cooling-device = <&CPU0 THERMAL_NO_LIMIT
> +                                                            THERMAL_NO_LIMIT>;
> +                            };
> +                    };
> +            };
> +
> +            /* ... */
> +    };
> +...
> -- 
> 2.20.1
> 



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux