[v1 2/6] arm64: dts: apq8016-sbc: Add CCI/Sensor nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Loic Poulain <loic.poulain@xxxxxxxxxx>

Add cci device to msm8916.dtsi.
Add default 96boards camera node for db410c (apq8016-sbc).

Signed-off-by: Loic Poulain <loic.poulain@xxxxxxxxxx>
Signed-off-by: Robert Foss <robert.foss@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 75 +++++++++++++++++++++++
 1 file changed, 75 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 037e26b3f8d5..a3e6982f4f93 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -495,6 +495,81 @@
 		wcnss@a21b000 {
 			status = "okay";
 		};
+
+		camera_vdddo_1v8: fixedregulator@0 {
+			compatible = "regulator-fixed";
+			regulator-name = "camera_vdddo";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		camera_vdda_2v8: fixedregulator@1 {
+			compatible = "regulator-fixed";
+			regulator-name = "camera_vdda";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-always-on;
+		};
+
+		camera_vddd_1v5: fixedregulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "camera_vddd";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-always-on;
+		};
+
+		cci@1b0c000 {
+			status = "ok";
+			i2c-bus@0 {
+				camera_rear@3b {
+					compatible = "ovti,ov5640";
+					reg = <0x3b>;
+
+					enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+					reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&camera_rear_default>;
+
+					clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+					clock-names = "xclk";
+					clock-frequency = <23880000>;
+
+					vdddo-supply = <&camera_vdddo_1v8>;
+					vdda-supply = <&camera_vdda_2v8>;
+					vddd-supply = <&camera_vddd_1v5>;
+
+					/* No camera mezzanine by default */
+					status = "okay";
+
+					port {
+						ov5640_ep: endpoint {
+							clock-lanes = <1>;
+							data-lanes = <0 2>;
+							remote-endpoint = <&csiphy0_ep>;
+						};
+					};
+				};
+			};
+		};
+
+		camss@1b00000 {
+			status = "ok";
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					csiphy0_ep: endpoint {
+						clock-lanes = <1>;
+						data-lanes = <0 2>;
+						remote-endpoint = <&ov5640_ep>;
+						status = "okay";
+					};
+				};
+			};
+		};
 	};
 
 	usb2513 {
-- 
2.20.1




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux