Re: [PATCH v3 3/4] phy: qcom-qmp: Add QMP V3 USB3 PHY support for SC7180

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Feb 12, 2020 at 04:51:27PM +0530, Sandeep Maheswaram wrote:
> Adding QMP v3 USB3 phy support for SC7180.
> Adding only usb phy reset in the list to avoid
> reset of DP block.
> 
> Signed-off-by: Sandeep Maheswaram <sanm@xxxxxxxxxxxxxx>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp.c | 38 +++++++++++++++++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index 7db2a94..dc300a9 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -1139,6 +1139,10 @@ static const char * const msm8996_usb3phy_reset_l[] = {
>  	"phy", "common",
>  };
>  
> +static const char * const sc7180_usb3phy_reset_l[] = {
> +	"phy",
> +};
> +
>  /* list of regulators */
>  static const char * const qmp_phy_vreg_l[] = {
>  	"vdda-phy", "vdda-pll",
> @@ -1265,6 +1269,37 @@ static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
>  	.is_dual_lane_phy	= true,
>  };
>  
> +static const struct qmp_phy_cfg sc7180_usb3phy_cfg = {
> +	.type			= PHY_TYPE_USB3,
> +	.nlanes			= 1,
> +
> +	.serdes_tbl		= qmp_v3_usb3_serdes_tbl,
> +	.serdes_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
> +	.tx_tbl			= qmp_v3_usb3_tx_tbl,
> +	.tx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_tx_tbl),
> +	.rx_tbl			= qmp_v3_usb3_rx_tbl,
> +	.rx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_rx_tbl),
> +	.pcs_tbl		= qmp_v3_usb3_pcs_tbl,
> +	.pcs_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_pcs_tbl),
> +	.clk_list		= qmp_v3_phy_clk_l,
> +	.num_clks		= ARRAY_SIZE(qmp_v3_phy_clk_l),
> +	.reset_list		= sc7180_usb3phy_reset_l,
> +	.num_resets		= ARRAY_SIZE(sc7180_usb3phy_reset_l),
> +	.vreg_list		= qmp_phy_vreg_l,
> +	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
> +	.regs			= qmp_v3_usb3phy_regs_layout,
> +
> +	.start_ctrl		= SERDES_START | PCS_START,
> +	.pwrdn_ctrl		= SW_PWRDN,
> +
> +	.has_pwrdn_delay	= true,
> +	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
> +	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
> +
> +	.has_phy_dp_com_ctrl	= true,
> +	.is_dual_lane_phy	= true,
> +};
> +
>  static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
>  	.type			= PHY_TYPE_USB3,
>  	.nlanes			= 1,
> @@ -2103,6 +2138,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
>  		.compatible = "qcom,ipq8074-qmp-pcie-phy",
>  		.data = &ipq8074_pciephy_cfg,
>  	}, {
> +		.compatible = "qcom,sc7180-qmp-usb3-phy",
> +		.data = &sc7180_usb3phy_cfg,
> +	}, {
>  		.compatible = "qcom,sdm845-qmp-usb3-phy",
>  		.data = &qmp_v3_usb3phy_cfg,
>  	}, {

I don't claim to be really knowledgable about this driver, but I confirmed
that this matches qmp_v3_usb3phy_cfg, except for the resets, since we don't
want to reset DP from the USB driver.

Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux