On Tue, Feb 04, 2020 at 05:16:34PM +0100, ansuelsmth@xxxxxxxxx wrote:
> If something like this is used, msm-timer require interrupts. Without this
> configuration, the device is unbootable as the system froze on system
> bootup.
>
> timer@200a000 {
> compatible = "qcom,kpss-timer", "qcom,msm-timer";
> interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
> IRQ_TYPE_EDGE_RISING)>,
> <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
> IRQ_TYPE_EDGE_RISING)>,
> <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
> IRQ_TYPE_EDGE_RISING)>,
> <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
> IRQ_TYPE_EDGE_RISING)>,
> <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
> IRQ_TYPE_EDGE_RISING)>;
> no-pretimeout;
> reg = <0x0200a000 0x100>;
> clock-frequency = <25000000>,
> <32768>;
> clocks = <&sleep_clk>;
> clock-names = "sleep";
> cpu-offset = <0x80000>;
> };
>
I think this is all wrong; the new property shows up in a node which
is completely unrelated to a watchdog. Maybe it wasn't such a good idea
to tie the watchdog to the timer node. At the very least, the situation
should be handled in the driver via of_table flags. If the situation can't
be handled that way, something is even more wrong. In that case it might
be better to revert commit 36375491a439 until that is sorted out properly.
Guenter
> > On Tue, Feb 04, 2020 at 04:21:01PM +0100, Ansuel Smith wrote:
> > > Some platform like ipq806x doesn't support pretimeout.
> > > As the driver check if there are available interrupts and ipq806x
> > > use msm-timer that require interrupts, the watchdog fail to probe
> > > as request_irq tries to use a ppi interrupt. Add an option to skip
> > > pretimeout setup and use the normal watchdog probe.
> > >
> > > Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
> > > ---
> > > drivers/watchdog/qcom-wdt.c | 5 ++++-
> > > 1 file changed, 4 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
> > > index a494543d3ae1..e689e97e883e 100644
> > > --- a/drivers/watchdog/qcom-wdt.c
> > > +++ b/drivers/watchdog/qcom-wdt.c
> > > @@ -189,6 +189,7 @@ static int qcom_wdt_probe(struct platform_device
> > *pdev)
> > > u32 percpu_offset;
> > > int irq, ret;
> > > struct clk *clk;
> > > + bool nopretimeout;
> > >
> > > regs = of_device_get_match_data(dev);
> > > if (!regs) {
> > > @@ -204,6 +205,8 @@ static int qcom_wdt_probe(struct platform_device
> > *pdev)
> > > if (!res)
> > > return -ENOMEM;
> > >
> > > + nopretimeout = of_property_read_bool(np, "no-pretimeout");
> > > +
> > > /* We use CPU0's DGT for the watchdog */
> > > if (of_property_read_u32(np, "cpu-offset", &percpu_offset))
> > > percpu_offset = 0;
> > > @@ -247,7 +250,7 @@ static int qcom_wdt_probe(struct platform_device
> > *pdev)
> > >
> > > /* check if there is pretimeout support */
> > > irq = platform_get_irq(pdev, 0);
> > > - if (irq > 0) {
> > > + if (!nopretimeout && irq > 0) {
> >
> > That is unnecessary; such platforms should simply not provide an
> interrupt.
> > Or, in other words, what is the point of assigning an interrupt to be used
> > for pretimeout if the platform doesn't support it ? And then to add yet
> > another attribute to tell the driver not to use it ?
> >
> > Guenter
> >
> > > ret = devm_request_irq(dev, irq, qcom_wdt_isr,
> > > IRQF_TRIGGER_RISING,
> > > "wdt_bark", &wdt->wdd);
> > > --
> > > 2.24.0
> > >
>
