Add device tree binding Documentation details for ipq6018 pinctrl driver. Co-developed-by: Rajkumar Ayyasamy <arajkuma@xxxxxxxxxxxxxx> Signed-off-by: Rajkumar Ayyasamy <arajkuma@xxxxxxxxxxxxxx> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx> Co-developed-by: Sivaprakash Murugesan <sivaprak@xxxxxxxxxxxxxx> Signed-off-by: Sivaprakash Murugesan <sivaprak@xxxxxxxxxxxxxx> Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx> --- [V5] * Addressed review comments from Rob * Ran dt bindings check and no errors were reported .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 162 +++++++++++++++++++++ 1 file changed, 162 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml new file mode 100644 index 0000000..0622258 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml @@ -0,0 +1,162 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block + +maintainers: + - Sricharan R <sricharan@xxxxxxxxxxxxxx> + +description: | + This binding describes the Top Level Mode Multiplexer block found in the + IPQ6018 platform. + +properties: + compatible: + const: qcom,ipq6018-pinctrl + + reg: + maxItems: 1 + + interrupts: + description: Specifies the TLMM summary IRQ + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + description: + Specifies the PIN numbers and Flags, as defined in defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + gpio-controller: true + + '#gpio-cells': + description: Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-ranges: + description: Documentation/devicetree/bindings/gpio/gpio.txt + maxItems: 1 + +#PIN CONFIGURATION NODES +patternProperties: + '.*-pin.*': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + allOf: + - $ref: "/schemas/pinctrl/pincfg-node.yaml" + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. The valid values are gpio1-80, sdc1_clk, sdc1_cmd, + sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_cmd, qdsd_data0, + qdsd_data1, qdsd_data2, qdsd_data3 + minItems: 1 + maxItems: 4 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac, + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0, + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c, + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi, + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi, + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi, + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi, + blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst, + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v, + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass, + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, + qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write, + sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, + uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + bias-pull-down: + type: boolean + description: The specified pin should be configured as pull down. + + bias-pull-up: + type: boolean + description: The specified pin should be configured as pull up. + + bias-disable: + type: boolean + description: The specified pin should be configured as no pull. + + output-high: + type: boolean + description: The specified pin is configured in output mode, driven + high. + + output-low: + type: boolean + description: The specified pin is configured in output mode, driven + low. + + required: + - pins + - function + + additionalProperties: false + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq6018-pinctrl"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 80>; + + serial3-pinmux { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; -- 2.7.4
