在 2020-01-03 14:33，rjliao@xxxxxxxxxxxxxx 写道：
在 2020-01-03 03:07，Matthias Kaehlcke 写道：
Hi Rocky,
On Fri, Dec 27, 2019 at 03:21:30PM +0800, Rocky Liao wrote:
This patch adds the HCI command timeout handling, it will trigger
btsoc
to report its memory dump via vendor specific events when hit the
defined
max HCI command timeout count. After all the memory dump VSE are
sent, the
btsoc will also send a HCI_HW_ERROR event to host and this will cause
a new
hci down/up process and the btsoc will be re-initialized.
Signed-off-by: Rocky Liao <rjliao@xxxxxxxxxxxxxx>
---
Changes in v2:
- Fix build error
Changes in v3:
- Remove the function declaration
- Move the cmd_timeout() callback register to probe()
- Remove the redundant empty line
drivers/bluetooth/hci_qca.c | 45
+++++++++++++++++++++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/drivers/bluetooth/hci_qca.c
b/drivers/bluetooth/hci_qca.c
index ca0b38f065e5..026e2e2cdd30 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -47,6 +47,8 @@
#define IBS_HOST_TX_IDLE_TIMEOUT_MS 2000
#define CMD_TRANS_TIMEOUT_MS 100
+#define QCA_BTSOC_DUMP_CMD 0xFB
+
/* susclk rate */
#define SUSCLK_RATE_32KHZ 32768
@@ -56,6 +58,9 @@
/* max retry count when init fails */
#define QCA_MAX_INIT_RETRY_COUNT 3
+/* when hit the max cmd time out count, trigger btsoc dump */
+#define QCA_MAX_CMD_TIMEOUT_COUNT 3
nit: MAX_CMD_TIMEOUTS?
Similar to QCA_MAX_INIT_RETRY_COUNT on which I commented earlier I
don't
think the 'QCA' prefix adds value here. The constant is defined in the
driver
itself and isn't related to hardware.
OK
+
enum qca_flags {
QCA_IBS_ENABLED,
QCA_DROP_VENDOR_EVENT,
@@ -123,6 +128,8 @@ struct qca_data {
u64 rx_votes_off;
u64 votes_on;
u64 votes_off;
+
+ u32 cmd_timeout_cnt;
nit: cmd_timeouts?
btusb is also using cmd_timeout_cnt, prefer to align with that
};
enum qca_speed_type {
@@ -1332,6 +1339,11 @@ static int qca_setup(struct hci_uart *hu)
if (!ret) {
set_bit(QCA_IBS_ENABLED, &qca->flags);
qca_debugfs_init(hdev);
+
+ /* clear the command time out count every time after
+ * initializaiton done
+ */
+ qca->cmd_timeout_cnt = 0;
} else if (ret == -ENOENT) {
/* No patch/nvm-config found, run with original fw/config */
ret = 0;
@@ -1462,6 +1474,38 @@ static int qca_power_off(struct hci_dev *hdev)
return 0;
}
+static int qca_send_btsoc_dump_cmd(struct hci_uart *hu)
+{
+ int err = 0;
The variable is pointless, just return 0 at the end of the function.
OK
+ struct sk_buff *skb = NULL;
+ struct qca_data *qca = hu->priv;
+
+ BT_DBG("hu %p sending btsoc dump command", hu);
+
+ skb = bt_skb_alloc(1, GFP_ATOMIC);
+ if (!skb) {
+ BT_ERR("Failed to allocate memory for qca dump command");
"These generic allocation functions all emit a stack dump on failure
when used
without __GFP_NOWARN so there is no use in emitting an additional
failure
message when NULL is returned."
Documentation/process/coding-style.rst
hence the logging is redundant, drop it.
OK
+ return -ENOMEM;
+ }
+
+ skb_put_u8(skb, QCA_BTSOC_DUMP_CMD);
+
+ skb_queue_tail(&qca->txq, skb);
+
+ return err;
+}
+
+static void qca_cmd_timeout(struct hci_dev *hdev)
+{
+ struct hci_uart *hu = hci_get_drvdata(hdev);
+ struct qca_data *qca = hu->priv;
+
+ BT_ERR("hu %p hci cmd timeout count=0x%x", hu,
++qca->cmd_timeout_cnt);
Is there any particular reason to print the counter in hex instead of
decimal?
Should this use bt_dev_err() since we have a hdev in this context?
OK
+
+ if (qca->cmd_timeout_cnt >= QCA_MAX_CMD_TIMEOUT_COUNT)
+ qca_send_btsoc_dump_cmd(hu);
+}
+
static int qca_regulator_enable(struct qca_serdev *qcadev)
{
struct qca_power *power = qcadev->bt_power;
@@ -1605,6 +1649,7 @@ static int qca_serdev_probe(struct
serdev_device *serdev)
hdev = qcadev->serdev_hu.hdev;
set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
hdev->shutdown = qca_power_off;
+ hdev->cmd_timeout = qca_cmd_timeout;
}
out: return err;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, a Linux Foundation Collaborative Project
