On Thu, Dec 19, 2019 at 04:48:47PM +0100, Ulf Hansson wrote:
> On Thu, 19 Dec 2019 at 15:34, Sudeep Holla <sudeep.holla@xxxxxxx> wrote:
> >
> > On Wed, Dec 11, 2019 at 04:43:43PM +0100, Ulf Hansson wrote:
> > > To enable the OS to better support PSCI OS initiated CPU suspend mode,
> > > let's convert from the flattened layout to the hierarchical layout.
> > >
> > > In the hierarchical layout, let's create a power domain provider per CPU
> > > and describe the idle states for each CPU inside the power domain provider
> > > node. To group the CPUs into a cluster, let's add another power domain
> > > provider and make it act as the master domain. Note that, the CPU's idle
> > > states remains compatible with "arm,idle-state", while the cluster's idle
> > > state becomes compatible with "domain-idle-state".
> > >
> > > Co-developed-by: Lina Iyer <lina.iyer@xxxxxxxxxx>
> > > Signed-off-by: Lina Iyer <lina.iyer@xxxxxxxxxx>
> > > Signed-off-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> > > ---
> > >
> > > Changes in v4:
> > > - None.
> > >
> > > ---
> > > arch/arm64/boot/dts/qcom/msm8916.dtsi | 57 +++++++++++++++++++++++++--
> > > 1 file changed, 53 insertions(+), 4 deletions(-)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > > index 8686e101905c..282c36c8fa3b 100644
> > > --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > > @@ -102,10 +102,11 @@
> > > reg = <0x0>;
> > > next-level-cache = <&L2_0>;
> > > enable-method = "psci";
> > > - cpu-idle-states = <&CPU_SLEEP_0>;
> > > clocks = <&apcs>;
> > > operating-points-v2 = <&cpu_opp_table>;
> > > #cooling-cells = <2>;
> > > + power-domains = <&CPU_PD0>;
> > > + power-domain-names = "psci";
> > > };
> > >
> > > CPU1: cpu@1 {
> > > @@ -114,10 +115,11 @@
> > > reg = <0x1>;
> > > next-level-cache = <&L2_0>;
> > > enable-method = "psci";
> > > - cpu-idle-states = <&CPU_SLEEP_0>;
> > > clocks = <&apcs>;
> > > operating-points-v2 = <&cpu_opp_table>;
> > > #cooling-cells = <2>;
> > > + power-domains = <&CPU_PD1>;
> > > + power-domain-names = "psci";
> > > };
> > >
> > > CPU2: cpu@2 {
> > > @@ -126,10 +128,11 @@
> > > reg = <0x2>;
> > > next-level-cache = <&L2_0>;
> > > enable-method = "psci";
> > > - cpu-idle-states = <&CPU_SLEEP_0>;
> > > clocks = <&apcs>;
> > > operating-points-v2 = <&cpu_opp_table>;
> > > #cooling-cells = <2>;
> > > + power-domains = <&CPU_PD2>;
> > > + power-domain-names = "psci";
> > > };
> > >
> > > CPU3: cpu@3 {
> > > @@ -138,10 +141,11 @@
> > > reg = <0x3>;
> > > next-level-cache = <&L2_0>;
> > > enable-method = "psci";
> > > - cpu-idle-states = <&CPU_SLEEP_0>;
> > > clocks = <&apcs>;
> > > operating-points-v2 = <&cpu_opp_table>;
> > > #cooling-cells = <2>;
> > > + power-domains = <&CPU_PD3>;
> > > + power-domain-names = "psci";
> > > };
> > >
> > > L2_0: l2-cache {
> > > @@ -161,12 +165,57 @@
> > > min-residency-us = <2000>;
> > > local-timer-stop;
> > > };
> > > +
> > > + CLUSTER_RET: cluster-retention {
> > > + compatible = "domain-idle-state";
> > > + arm,psci-suspend-param = <0x41000012>;
> >
> > If I followed the thread correctly, we are now just using the param as is
> > without any extra logic like ORing like before. i.e. The domain state
> > parameter overrides the any param below it in the hierarchy.
> >
> > If that's correct, then
>
> That's correct!
>
Thanks for the confirmation.
--
Regards,
Sudeep
