Hi Rajeshwari,
On Thu, Nov 28, 2019 at 3:25 PM Rajeshwari <rkambl@xxxxxxxxxxxxxx> wrote:
>
> Add TSENS node and user thermal zone for TSENS sensors in SC7180.
>
> Signed-off-by: Rajeshwari <rkambl@xxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 527 +++++++++++++++++++++++++++++++++++
> 1 file changed, 527 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 666e9b9..6656ffc 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -911,6 +911,26 @@
> status = "disabled";
> };
>
> + tsens0: thermal-sensor@c263000 {
> + compatible = "qcom,sc7180-tsens","qcom,tsens-v2";
> + reg = <0 0x0c263000 0 0x1ff>, /* TM */
> + <0 0x0c222000 0 0x1ff>; /* SROT */
> + #qcom,sensors = <15>;
> + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow";
> + #thermal-sensor-cells = <1>;
> + };
> +
> + tsens1: thermal-sensor@c265000 {
> + compatible = "qcom,sc7180-tsens","qcom,tsens-v2";
> + reg = <0 0x0c265000 0 0x1ff>, /* TM */
> + <0 0x0c223000 0 0x1ff>; /* SROT */
> + #qcom,sensors = <10>;
> + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uplow";
> + #thermal-sensor-cells = <1>;
> + };
> +
> spmi_bus: spmi@c440000 {
> compatible = "qcom,spmi-pmic-arb";
> reg = <0 0x0c440000 0 0x1100>,
> @@ -1121,6 +1141,513 @@
> };
> };
>
> + thermal-zones {
> + cpu0-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 1>;
> +
> + trips {
> + cpu0_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu0_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu0_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
Where are the cooling maps for all the cpu thermal zones? A passive
trip point w/o a cooling map is not of much use. If you are waiting
for cpufreq support to land before adding them, then remove the
passive trip points for now and add them along with the cooling maps
when you have cooling devices.
> + };
> + };
> +
> + cpu1-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 2>;
> +
> + trips {
> + cpu1_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu1_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu1_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu2-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 3>;
> +
> + trips {
> + cpu2_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu2_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu2_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu3-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 4>;
> +
> + trips {
> + cpu3_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu3_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu3_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu4-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 5>;
> +
> + trips {
> + cpu4_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu4_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu4_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu5-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 6>;
> +
> + trips {
> + cpu5_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu5_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu5_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu6-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 9>;
> +
> + trips {
> + cpu6_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu6_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu6_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu7-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 10>;
> +
> + trips {
> + cpu7_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu7_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu7_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu8-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 11>;
> +
> + trips {
> + cpu8_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu8_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu8_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + cpu9-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&tsens0 12>;
> +
> + trips {
> + cpu9_alert0: trip-point0 {
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu9_alert1: trip-point1 {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu9_crit: cpu_crit {
> + temperature = <110000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
