[PATCH v2 3/3] dt-bindings: phy: qcom-qusb2: Add SC7180 QUSB2 phy support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add QUSB2 phy entries for SC7180 in device tree bindings.

Signed-off-by: Sandeep Maheswaram <sanm@xxxxxxxxxxxxxx>
---
 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
index 3ef94bc..5eff9016 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
@@ -18,6 +18,7 @@ properties:
     enum:
       - qcom,msm8996-qusb2-phy
       - qcom,msm8998-qusb2-phy
+      - qcom,sc7180-qusb2-phy
       - qcom,sdm845-qusb2-phy
 
   reg:
@@ -66,7 +67,7 @@ properties:
         It is a 6 bit value that specifies offset to be
         added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
         tuning parameter that may vary for different boards of same SOC.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
     $ref: /schemas/types.yaml#/definitions/uint32
 
   qcom,hstx-trim-value:
@@ -75,7 +76,7 @@ properties:
         output current.
         Possible range is - 15mA to 24mA (stepsize of 600 uA).
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is 22.2mA for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
@@ -84,7 +85,7 @@ properties:
         It is a 2 bit value that specifies pre-emphasis level.
         Possible range is 0 to 15% (stepsize of 5%).
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is 10% for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
@@ -94,7 +95,7 @@ properties:
         pre-emphasis (specified using qcom,preemphasis-level) must be in
         effect. Duration could be half-bit of full-bit.
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is full-bit width for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux