On Thu 21 Nov 16:51 PST 2019, Matthias Kaehlcke wrote:
> Hi Sandeep,
>
> On Fri, Nov 15, 2019 at 10:53:41AM +0530, Sandeep Maheswaram wrote:
> > Add nodes for DWC3 USB controller, QMP and QUSB PHYs.
> >
> > Signed-off-by: Sandeep Maheswaram <sanm@xxxxxxxxxxxxxx>
> > Reviewed-by: Stephen Boyd <swboyd@xxxxxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/qcom/sc7180-idp.dts | 25 ++++++++
> > arch/arm64/boot/dts/qcom/sc7180.dtsi | 105 ++++++++++++++++++++++++++++++++
> > 2 files changed, 130 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > index 666e9b9..2c7dbdc 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> >
> > ...
> >
> > + usb_1: usb@a6f8800 {
> > + compatible = "qcom,sc7180-dwc3", "qcom,dwc3";
> > + reg = <0 0x0a6f8800 0 0x400>;
> > + status = "disabled";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + dma-ranges;
> > +
> > + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
> > + <&gcc GCC_USB30_PRIM_MASTER_CLK>,
> > + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
> > + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
> > + <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
> > + clock-names = "cfg_noc", "core", "iface", "mock_utmi",
> > + "sleep";
> > +
> > + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
> > + <&gcc GCC_USB30_PRIM_MASTER_CLK>;
> > + assigned-clock-rates = <19200000>, <150000000>;
> > +
> > + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "hs_phy_irq", "ss_phy_irq",
> > + "dm_hs_phy_irq", "dp_hs_phy_irq";
> > +
> > + power-domains = <&gcc USB30_PRIM_GDSC>;
> > +
> > + resets = <&gcc GCC_USB30_PRIM_BCR>;
> > +
> > + usb_1_dwc3: dwc3@a600000 {
> > + compatible = "snps,dwc3";
> > + reg = <0 0x0a600000 0 0xe000>;
> > + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> > + iommus = <&apps_smmu 0x540 0>;
> > + snps,dis_u2_susphy_quirk;
> > + snps,dis_enblslpm_quirk;
> > + phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
> > + phy-names = "usb2-phy", "usb3-phy";
> > + };
>
> I see the following message at boot:
>
> [ 4.248436] dwc3 a600000.dwc3: Failed to get clk 'ref': -2
>
dwc3-qcom picks up the clocks per the names of the binding, but then
dwc3 tries to pick up the same clocks based on the generic names.
At some point it would be nice to figure out how to have these two play
nice with each other, but for now it's a "harmless" error print - which
has consumed many hours of unnecessary debugging by various people...
Regards,
Bjorn
